Watch Repairs Help & Advice
SECTION RULES
If you are a new member, we would consider it polite for you to introduce yourself here before posting your questions.
Subforums
-
- 4.6k
- posts
-
New to watch repair ** Safe Zone For Learner Watch Repairers **
Discussing subjects relating to learner watch repairers.
More experienced repairers - please guide learners with patience and respect
- 9.6k
- posts
-
- 3.1k
- posts
-
- 6.7k
- posts
-
- 1.4k
- posts
-
- 3.2k
- posts
-
- 2.3k
- posts
-
- 1.7k
- posts
-
- 1.2k
- posts
-
- 966
- posts
-
- 2.7k
- posts
-
- 4.1k
- posts
-
- 407
- posts
8984 topics in this forum
-
What Can You Do After Adjusting Watch Timing Advance Or Retarding The Balance Has Come To It's Maximum 1 2
- 35 replies
- 8.7k views
-
- 11 replies
- 8.7k views
-
- 26 replies
- 8.7k views
-
- 17 replies
- 8.6k views
-
- 4 replies
- 8.6k views
-
- 4 replies
- 8.6k views
-
- 26 replies
- 8.6k views
-
- 15 replies
- 8.6k views
-
- 5 replies
- 8.6k views
-
- 2 replies
- 8.6k views
-
- 11 replies
- 8.6k views
-
- 17 replies
- 8.6k views
-
- 6 replies
- 8.6k views
-
- 5 replies
- 8.6k views
-
- 14 replies
- 8.6k views
-
- 17 replies
- 8.6k views
-
- 5 replies
- 8.6k views
-
- 13 replies
- 8.6k views
-
- 15 replies
- 8.6k views
-
- 9 replies
- 8.6k views
-
- 12 replies
- 8.6k views
-
- 4 replies
- 8.6k views
-
- 24 replies
- 8.6k views
-
- 6 replies
- 8.6k views
-
- 10 replies
- 8.6k views
-
Topics
-
-
Posts
-
-
Once you are aware of the problem, you can adjust as necessary. I have a couple of the Omega 10xx, and they are not my favourites. They seem a bit flimsy and not as solid as previous generation Omega. But I think that's true of a lot of movements from the 70-80s. For me, the 50-60s is the peak in watch movements, where the design criteria was quality, not saving the last penny. -
Thanks for this post MikePilk, I just came across a similar problem with an Omega 1022. The problem I had was the seconds pinion spring was bent out of shape and did not even engage with the wheel properly, so the seconds hand was not moving at all. (no power loss though :) I removed the automatic module so I could access the spring and work on it. Once I bent it back close to the right shape, I experienced the same problem you reported about power loss. Many tweaks later, and the seconds hand is moving properly again, with amplitude back to good numbers again. Cheers -
After cleaning up the pivots, I made bushes on the lathe. At this point I've pressed in 6 bushes (3 sets) and the wheels turn smooth. What I can also tell you, is that I'm not looking forward to final assembly. Getting the pivots aligned seems to get exponentially more difficult with each wheel that is added. -
Islands are interesting places to live depending upon their size and other factors. This is a bigger island and it has a bridge to get there at least on one end. It's also big enough that you don't have to go someplace else to get things typically. It can be a problem if you get a job in Seattle though. Yes I've known of people who commuted from the island to Seattle for a job and I don't quite remember how many hours it took but it took a long time. So basically islands are nice if you don't have to leave very often.
-
