Your Walkthroughs and Techniques
Post descriptive walkthroughs of watches you have stripped down and serviced and/or repaired, parts you have made or techniques you wish to share.
This is an interesting section where we post our challenges and how we have over-come them. You can also post walkthroughs and share your techniques.
SECTION RULES
This section is strictly for those posting real step-by-step walkthroughs of actual repair or servicing techniques relating to watch repair and/or horology in general. The idea is that we help each other by describing or sharing our repair techniques, or telling a story of how we have progressed.
If you are not posting step-by-step walkthroughs, such as - you would just like to showcase a completed repair job, then please choose a more appropriate sub-forum for your content. If your post is not deemed to be a legitimate walkthrough then a moderator will move your post to the appropriate section without notice. Thank you for your co-operation.
- You must be a member with at least 10 posts on the forum in order to contribute in this section
365 topics in this forum
-
- 33 replies
- 19.7k views
-
- 32 replies
- 14.9k views
-
- 31 replies
- 17.6k views
-
- 31 replies
- 18.5k views
-
- 31 replies
- 38.5k views
-
- 31 replies
- 10.3k views
-
- 31 replies
- 27.6k views
-
- 30 replies
- 48.3k views
-
- 30 replies
- 15.6k views
-
- 30 replies
- 14.5k views
-
- 29 replies
- 60.4k views
-
- 29 replies
- 18.3k views
-
- 29 replies
- 25.5k views
-
- 28 replies
- 37.9k views
-
- 28 replies
- 8.5k views
-
- 27 replies
- 11.2k views
-
- 27 replies
- 13.5k views
-
- 26 replies
- 13.9k views
-
- 26 replies
- 6.1k views
-
- 26 replies
- 15.6k views
-
- 25 replies
- 15.1k views
-
- 25 replies
- 8.3k views
-
- 25 replies
- 11.5k views
-
- 25 replies
- 10k views
-
- 25 replies
- 5.9k views
-
Topics
-
-
Posts
-
Oh well, if Master @nickelsilver says it's the way to go, then it is the way to go! I stand corrected! 🫡 Are there any other places where you're supposed to remove the epilame from the contact point of rubbing? I don't think so! Thanks for the effort @Neverenoughwatches, much appreciated! 🙂👍 -
By JertiNeron892 · Posted
If you're seeking advice for your "Harvard GSD" MArch II application essays, I'd recommend taking a thoughtful approach. Reflect deeply on your experiences, passions, and goals, and tailor your essays to showcase your unique perspective and potential contributions to the program. As for resources, I recently stumbled upon a gret platform for essays, and I must say, it's been quite helpful. Their selection of pre-written essays covers a wide range of topics, and their professional writers can also assist with custom essays tailored to your specific needs. Check out their offerings here: https://essaypro.com/essays-for-sale. Remember, authenticity is key in your application essays. Good luck! -
By ManSkirtBrew · Posted
For clarity and ease of testing, I redid that diagram, flipping the circuit to match the layout of the physical watch. -
Hello, Thanks for the reply. The old jewel will get pushed out from the "outside" which is the dial side. The new jewel will get pressed in from the inside (shown below) which is the movement side, correct? And the old jewel and spring will get pushed from the is the "outside" which is the dial side. Thank you very much for the information. I will take out the KIF spring and save it. Will update when the new jewel is in place! Regards, Joe -
It's a little circlip style retaining clip to keep the pinion from riding up out of position.
-
