Jump to content
  • The watch repair course and videos section has moved - if you are a Patron via Patreon or a WRT Subscriber, kindly create an account here: https://www.watchrepairlessons.com, if you have not done so already, in order to continue with your access to the Early Access and Ad-Free videos.

    The Patron and Subscribers section in the WatchRepairLessons.com dashboard (direct link) will detail all your subscription details. 

    This will help me consolidate all my videos under one roof rather than maintaining two separate systems, and it will also help clean up WRT a bit.

    If you have any questions please message me, Mark :)

Clock Corner

Post all things relating to clocks in this forum. Yes this is a watch forum, but we still love all things that go tick and that includes clocks.

356 topics in this forum

    • 92 replies
    • 7,580 views
  1. Repair Of A Carriage Clock 1 2 3 4

    • 75 replies
    • 6,265 views
    • 70 replies
    • 5,958 views
    • 56 replies
    • 808 views
    • 54 replies
    • 752 views
    • 50 replies
    • 828 views
    • 48 replies
    • 4,516 views
    • 48 replies
    • 586 views
    • 43 replies
    • 2,793 views
  2. Clock Oiling 1 2

    • 39 replies
    • 8,166 views
    • 36 replies
    • 7,070 views
    • 36 replies
    • 591 views
    • 34 replies
    • 3,868 views
    • 33 replies
    • 454 views
    • 32 replies
    • 6,939 views
    • 31 replies
    • 515 views
    • 30 replies
    • 281 views
  3. Black Slate Renovation? 1 2

    • 29 replies
    • 10,250 views
  4. wall clock oil 1 2

    • 29 replies
    • 3,125 views
    • 29 replies
    • 428 views
  5. Looks like Chinese crap. 1 2

    • 28 replies
    • 4,962 views
    • 27 replies
    • 2,738 views
    • 27 replies
    • 953 views
    • 27 replies
    • 314 views
    • 26 replies
    • 2,218 views
  • Recent Topics

  • Posts

    • Hi guys, I have a problem setting the time with this watch. The first time around, the minute hand goes around ok, the second time it stops at around 10 to and wont go backwards or forwards. It just sticks there. If I push the crown back in the watch works fine and when the minute hand gets past this point, I can then pull out the crown and move the hands again.  Can anyone shed some light on this?
    • If you are in no hurry I could stripp one keyless down and make a small tutorial of it.  I seldom use the Moebius 8000 anymore but put it on at request   If one would buy some luricants and don't bother  about the mainspring it would be a setup like this.. Fine oil Moebius 9010 - On the escapement parts (It's here you can use Moebius 8000) Thick oil Moebius HP-1300 On the most other parts which needs to be lubricated  Grease Moebius 9504 Like on the winding pinion and so on.. Special for pallet stones Moebius 9415.  
    • Okay, I made a bit of time to get this project moving forward, it may take me a year at this rate. I had to get another cylinder as the original had all the pins bent. As you would expect nothing fits, therefore I had to bush the new cylinder to fit the shaft. I also had time to polish the fly and rebush it. A note, I added a photo of getting it level for those new to clock repair (horizontal and vertical) as these are long pins and if off a bit forget about them working smoothly. 
    • Thank you for your introduction and welcome to this friendly forum.
    • A faceted crystal has ..faces but not a lip. Seiko did not use glue often, and the crystal will not leave by pushing with a thumb. Fortunately, Seiko helps watch repairers by classifying and documenting the case construction, here we have an "A" as stamped on the case back. Attached the guide. A good discussion is at https://www.plus9time.com/seiko-case-back-information BTW, I recommend the OP to use the "Watch Repairs Help & Advice" section when it's repair question like this. One advantage is that there answers can be rated and marked as resolving.   1982.03 Seiko Case Servicing Guide.pdf
×
×
  • Create New...