Your Walkthroughs and Techniques
Post descriptive walkthroughs of watches you have stripped down and serviced and/or repaired, parts you have made or techniques you wish to share.
This is an interesting section where we post our challenges and how we have over-come them. You can also post walkthroughs and share your techniques.
SECTION RULES
This section is strictly for those posting real step-by-step walkthroughs of actual repair or servicing techniques relating to watch repair and/or horology in general. The idea is that we help each other by describing or sharing our repair techniques, or telling a story of how we have progressed.
If you are not posting step-by-step walkthroughs, such as - you would just like to showcase a completed repair job, then please choose a more appropriate sub-forum for your content. If your post is not deemed to be a legitimate walkthrough then a moderator will move your post to the appropriate section without notice. Thank you for your co-operation.
- You must be a member with at least 10 posts on the forum in order to contribute in this section
380 topics in this forum
-
- 16 replies
- 28.5k views
-
- 3 replies
- 32.7k views
-
- 14 replies
- 8.1k views
-
- 8 replies
- 3.9k views
-
- 7 replies
- 6.1k views
-
- 12 replies
- 7k views
-
- 15 replies
- 5.9k views
-
- 8 replies
- 5.1k views
-
- 4 replies
- 5.5k views
-
- 20 replies
- 5.6k views
-
- 30 replies
- 19.4k views
-
- 2 replies
- 9.1k views
-
- 15 replies
- 5.3k views
-
- 19 replies
- 7k views
-
- 4 replies
- 4.1k views
-
- 19 replies
- 8.9k views
-
- 9 replies
- 4.9k views
-
- 19 replies
- 8.7k views
-
- 1 reply
- 1.9k views
-
- 13 replies
- 9k views
-
- 12 replies
- 4.8k views
-
- 1 reply
- 3.9k views
-
- 30 replies
- 57.3k views
-
- 4 replies
- 13.3k views
-
- 3 replies
- 5.6k views
.jpg.6225a64433578a11e0218b27c20b13f5.thumb.jpg.d82b0cd1e370f3a3a59a06afa957d184.jpg)
-
Topics
-
-
Posts
-
You might like to see the contraption that I made for indexing on my Chinese lathe. This is a 4 inch rotary table with dividing plates that I attached to my lathe mandrel using a drawbar. It is completely manually operated. No electronics or computer needed. I have used it to make a 60 tooth clock wheel. I use a Sherline headstock on a vertical slide to drive the gear cutter. The wheel blank is mounted on an aluminium "superglue arbor." This is the modern equivalent of a shellac chuck, and allows the wheel to be centre bored, trued and the teeth cut in a single setup, ensuring that concentricity is maintained. The finished wheel after crossing. I have not tried to make small watch parts on this lathe. The runout on the mandrel bearings may be too high for that. I won't know unless I try. -
By coreymsnow · Posted
Y'all are very helpful, I can't thank you enough for the insights. -
By FabioBastardo · Posted
Will do. Funny it doesn’t have a makers name. -
By Neverenoughwatches · Posted
Andygsi said he was done after last week and think old hippy has gone the same way😞. I'll miss both of them, especially the old fella. -
Hello from the great state of Tennessee. I live just a couple of miles from the geographical center of Tennessee so when I say that I live in middle Tennessee, it's the truth. Over the past couple of years I have really grown to love Hamilton pocket watches. Specifically the RR lever set ones. I have about 20 Hamiltons & most of them are 21 jewel RR watches. One of these days I'm gonna dive in & see if I can take one apart, clean & reassemble it. The 940's I have are too beautiful for me to risk destroying so I plan on getting a running cheap movement to experiment on. I am looking forward to reading & learning about the process of watch repair. I'm happy to be here!
-
.thumb.jpg.cb17a66989f1e796fd4217db2e9ca9df.jpg)
