Jump to content

My Practical Exercises, Course Level 2


Recommended Posts

Hi everyone!

I made log of my activities with photos of my practical exercises for WR Course level 2. It's in the PDF file attached. 

I had some scary moments doing this. One of them was the balance cock that slid off the movement onto the table while dangling by the hairspring. Furthermore, I discovered that end stone jewels and shock springs also like to fly, causing lengthy search parties  :o

 

Cheers, Mark

 

Watch Repair Course L2 v2.pdf

  • Like 5
Link to comment
Share on other sites

Hi Nice job and well done ,like most of us you find watch parts can take off at an alarming rate and disappear, When removing and fitting such parts its as well to either use rodico to hold them in place or work inside a large clear plastic bag that way is the part/parts take off they are retained in the bag. Get a large bag and cut the bottom off so you can get a hand in eiither end  and carry out the required operation, then work outside the bag for normal operations,,   Might save time and your knees.:thumbsu:

  • Like 2
  • Haha 1
Link to comment
Share on other sites

Nicely done Mark!

I love it when luck is on my side, as you found when the lyre spring landed in your tray!

These lyre springs should be captive, but as you found, some are and some aren't.

Is this a real Seagull or a copy of the Seagull, because the cheaper copy's have the lyre spring problem?

What did you use to rinse the parts with? If you used more Naptha, it'll leave a fine residue, which won't be good when oiling.

Link to comment
Share on other sites

Nicely done!

Both the movement and the .pdf. I still say I have a colony of ants that are secretly building a watch from all the tiny parts they've carried away from my floor. ;) They do love to fly in the strangest directions and end up in the oddest places (assuming you can find them at all).

When your shock spring arrives and you get the movement running, I'd suggest you give it a good wind and let it run for a day or three before you pop it on the timegrapher. Freshly serviced movements usually need a couple of days to "settle in".

And, what's your next project? I'd recommend something with an ETA 2824 variant (Sellita 220 or Seagull ST2130). They are smaller than the ST36 and have a date or day/date complication. They are common and parts are easy to get when if you send them flying into oblivion. I'd hold off on the Rolex for another week. :D

 

Link to comment
Share on other sites

  • 2 weeks later...

I just did a similar exercise with an anonymous Chinese movement, and had the same problem with the Incabloc springs. Mine didn't fly neatly into my parts tray like yours; it flew to the inside of the left lens of my glasses, and stuck there via static charge or something! I didn't find it until I took my glasses off in frustration after ran exhaustive search. I eventually broke my spring as well, but instead of ordering another, I just won't be messing with cheap Chinese movements any more and will break this movement down for screws and jewels and what have you. My neighbor does steampunk art, so he'll probably get some of the larger shiny pieces. :-)

Link to comment
Share on other sites

  • 3 weeks later...

I had the same problem with the lyre spring on my 6497 clone... Flew off 3 or 4 times... but luckily found it each time. Good tip about the plastic bag @watchweasol! I may well go with that in future. Lyre springs are turning into my pet hate already. I broke a tiny one on the first practice watch I got to work on (FHF ST 96) barely touched the arm and snapped clear off... it was about the last thing I was doing after a full clean and reassembly too... I ordered a new one (not that it is economically worth it, the watch cost £1.70) but I didn't want to leave it unfinished now I had gone so far, with the particular lower shock setting the movement has it will give me practice removing and replacing the setting too.

Link to comment
Share on other sites

Good write-up, MarkK.  That cannon pinion does take some force, but the positive snap will let you know it's home.  I like your pictures. 

If I'm not mistaken, it's ill advised to lubricate the pallet bridge pinions, please excuse me if I read incorrectly.  You may have been referring to the exit stone as you mentioned later.   

I don't know where I saw it, but this watchmaker oiled the escape wheel from underneath, using the two holes from which the pallet stones are visible.  He used an "L" shaped oiler, and held a tiny droplet of oil on it, and allowed each tooth to get a small smear as they passed by.  Now THAT'S dexterity.  That's got to be one of the most impressive, unorthodox things I've seen. 

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I think if you want to play Billy big b.ollocks then you have to have something up your sleeve, anyone that knows how to fight, plays dirty. Lets face it a lot of folk that voted for Brexit just rolled uk their sleeves to say up yours EU hoping for good changes. We have idiots for leaders and probably none of them clever enough to clean the shitty stick they were given. I didnt vote, what will be will be.
    • I voted leave too, my reasoning was the the EU is undemocratic, no elected officials. I don't regret it but I  am sad that both sides acted like petulant toddlers.  Shameful.  I'm not on other forums but if I was and left this site, would you shun me? Of course not, we aren't petulant toddlers.  
    • This is a type of tool that may be suitable to remove the bezel - though note that I'm pretty sure the watch should be face down - not face up, as in some of the photos of these tools on amazon & ebay! If you try one one of those, put the movement screws back in first to avoid accidents. https://www.amazon.co.uk/Removal-Professional-Remover-Watchmaker-Diameter/dp/B09XCH4QVN?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=A296NCMMFVXSDN&th=1  
    • Hi, I’m constantly asking my wife to help me with removing the stem in order to complete casing. To expand, this is not a challenge for me when the setting lever is secured by a screw (older calibers). However when the setting lever is attached to a spring loaded setting lever axel, like on more modern calibers, I simply don’t see how to apply enough pressure on the button to get the stem out short of putting the movement face down with the dial and hands attached, which I’m loath to do in order to avoid damaging the dial/hands? what technique should I be using? thanks  
    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
×
×
  • Create New...