Jump to content

Stereo Microscope


Recommended Posts

After VAT, shipping, and the Pound to USD exchange rate it became cost prohibitive.

I ordered an Amscope SE-400-Z instead. 10X and 20X pairs with X1 objective. I also won’t have to buy a voltage converter.

I hope it works just as well as the Brunel BM-1.


Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

  • 4 weeks later...

Santa left me one of these under the tree :thumbsu:

I like to take this quiet time to clean and redress all my tools and equipment.

The microscope was used to check my tweezers, screwdrivers and holders, the screen gives a great picture of the critical parts and is much better than using an eyeglass.  My tweezers in particular now have complete contacts (no bent up end, flat faces etc) and square ends, so hopefully fewer parts will go flying away.  They certainly seem to pick-up better.  My drivers were manly ok with only the odd burr to remove.  The edges on my holders are now better and seem to hold better.

Can't wait to use on watch movements and maybe go back and sort out some the messed up hairsprings !!!!

Link to comment
Share on other sites

I also purchased one of these thanks @canthusand @transporter

I too use it for dressing tweezers, screwdrivers and the like but for watch movements I would not be without my long arm microscope for most of the work....However it is good for recording a dismantle process on a micro sd card for later reference or in laymans terms Where the b..... hell does that piece go.

Link to comment
Share on other sites

  • 2 weeks later...

I use an Carl Zeiss Stemi DV4 Stereo Microscope to inspect the jewels with, before I used it as one is supposed to but nowadays I have become a bit lazy and put a cheap USB camera on the ocular. Took me 22 minutes to make it with a 3D printer.
One can get quite a nice picture on a computer screen with a setup like that and even take one odd picture on for example a cap jewel.

USB_Zeiss.jpg

Stemi DV4.jpg

  • Like 2
Link to comment
Share on other sites

5 hours ago, mlfloyd1 said:

Elevation speaking, when working on watches should the microscope be used on top of the watch bench or on top of a standard desk?

I would guess that depends on how long you work by the microscope. At a labaratory one mostly costum fit the microscope to fit your hight and so on. I use a standard desk but have an adjustable chair instead.


Some of our yonger personel even likes to stand on a ergonomic rubber matt instead of sitting.
Here is some instructions from Leica about the matter.

 

  • Like 2
Link to comment
Share on other sites

Reading this thread has me really wanting a stereo microscope.  I'm just a watch hobbyist, but I also do quite a bit of work on smallish firearm assemblies.  I've been looking at scopes like some of the 10-20x ones on Ebay for over a year now.  There is one that gives an 8" working area, which seems like it would be adequate.  Some times, even when using a loop I will bump my screwdriver hand with the loop. A little separation seems like it would be a nice thing.

From this thread, it sounds like the 10x power is the most utilized?

Link to comment
Share on other sites

  • 6 months later...

Just to be clear: this is being sold by the Horology Club that I am a member of; I won’t benefit from any sale but the club will (which is a good thing!). Mods please feel free to nuke this post if that crosses any lines.

 

With that out of the way, I’d just like to point out a large Zeiss microscope that is being ebayed at the moment in Essex, England. Listing is 254317526719

People may not notice it as it is not listed under watch or clock tools.

 

It’s a medical quality ‘scope on a blooming big stand! From what I’m told the working distance is perfectly suitable for watches and clocks (depending of course on how big your clock tools are!).

 

So If anyone is in the market for a decent quality ‘scope in that area it could be of interest to you.

 

 

Sent from my iPad using Tapatalk

Link to comment
Share on other sites

6 hours ago, oldhippy said:

I’ve just had a look. Quite an impressive piece.  

We don't need to nuke your post. :D

Thanks OH. I'd have the thing myself but I already have a stereo scope, and the first time my wife saw the big stand she would no doubt string me up from it!

Link to comment
Share on other sites

  • 1 month later...

Why a stereo microscope is recommended instead of a single lens one? As opposed to the traditional loupe recommended in lieu of a stereo visor?

Does anyone know of an especially small and lightweight model? 

Edited by jdm
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • It shouldn't be attached    The pinions look independent of each other, not in alignment,  but the clip is bothering me or have you just placed that on the pivot end? 
    • What this extra disk next to the pinion? Thats not part of the assembly 
    • It looks like the canon pinion function is part of this great wheel. The pinion nearest the clip runs the minute wheel on the dual side. The pinion nearest the wheel is driven by a small wheel from under the setting lever cover plate that engages in hand setting position.    So when assembled the crown was driving the whole great train. Does this mean the pinions are too tight? Should I attempt to disassemble this great wheel and lubricants?
    • Picking up this side-tracked post again as I just removed a balance staff of a 1920's Omega (35,5L-T1) I was impressed by the way @Delgetti had his setup when he had to change out a balance-staff (https://www.watchrepairtalk.com/topic/28854-new-balance-staff-not-riveting-to-balance/page/2/#comment-244054 Not only that, but also the idea of removing the seat first before punching the staff out from the seat-side, avoiding the whole discussion of the rivet yes/no enlarging the hole. I didn't have the fancy clamps & tools Delgetti has, so I used my screw-head polishing tool. Initially I used #1500 grit diamond paste on the steel wheel, which kinda worked, but very slow. I changed to #800 grit diamond paste, which worked better, but still slow. Then I glued #240 sanding paper to the steel disk; That worked and the disk was hand-driven. Once close to the balance wheel, I took the sanding paper off and continued with #800 diamond paste. One can only do this when the balance wheel sits true on the staff and has no "wobble". I went on grinding until I saw some diamond paste on the rim of the balance wheel. This was as far as I could grind and it seemed that there wasn't much left of the seat. Carefully, with my staking set, I knocked the staff from the seat-side out. Turns out that the thickness of the seat left, now a small ring, was only 0.1mm. The balance wheel hole is in perfect shape and no damage done to the wheel at all. Of course, if the wheel has a "wobble" or isn't seated true on the balance staff, you can't get as close and there will be more left of the seat. In my case, it worked perfect 🙂 I'm very happy how this method worked out ! 😊  
×
×
  • Create New...