Jump to content

How the heck do you get rid of dust on crystal (inside)


Recommended Posts

Please tell me, how can you effectively remove the dust particle completely? I found that it's almost impossible, I used air, clothes that should attract dust bla bla but there's always some micro particle saying hello from there. What is the spell??

Link to comment
Share on other sites

Clean Rodico can be used, but it also leaves a very light smear. I create a very thin cone of it, and then dab the final pieces of dust.

Can sometimes use pure water (plus a blower to get rid of beads of water when drying).

Link to comment
Share on other sites

3 hours ago, chriz74 said:

I cleaned it with water but if you dry it with a dryer water will leave shrouds

Clean with water, blow what water you can off, dry it, then with a cotton rag rub over it to remove any water stains. You can buy microfibre cloths and other expensive ones but a bit of clean cotton shirt will work just as well for removing water stains. Any bits of dust that do appear off cloth will then blow straight off.

Link to comment
Share on other sites

If it's glass, I use isopropyl alcohol with a glass cleaning microfibre to remove grease/dirt.
Then I spritz with distilled water to collect any leftover fibres, blow dry with a compressed air can to remove majority of water then finish off with hairdryer.

Sent from my Honor 5c

Link to comment
Share on other sites

What I find useful, are a set of fine brushes I bought in the poundshop--the sets women use for doing nail painting, included in this set is a very fine fan shaped one just about right for crystal inner surface combined with an air-blower bulb, about £3 from ebay to do the dial and crystal/case before refitting. Since Ive had these, not had any issues with fibres or specks in/on the dial/crystal

Watch tools dont need to cost the earth, just as well--I'm a mega-cheapskate!

Edited by Alastair
Link to comment
Share on other sites

1 hour ago, Alastair said:

What I find useful, are a set of fine brushes I bought in the poundshop--the sets women use for doing nail painting, included in this set is a very fine fan shaped one just about right for crystal inner surface combined with an air-blower bulb, about £3 from ebay to do the dial and crystal/case before refitting. Since Ive had these, not had any issues with fibres or specks in/on the dial/crystal

Watch tools dont need to cost the earth, just as well--I'm a mega-cheapskate!

Can you post pictures?

Link to comment
Share on other sites

I was being driven to despair by one case with acrylic glass - just couldn't get rid of the last bits of dust.

Then I found this device on ebay - sold as a camera sensor cleaner (a couple of £ from China).

It's basically a bit of solid silicone on a stick. You dab at the bits of dust and it doesn't leave any marks

 

20170409_182533.jpg

  • Like 1
Link to comment
Share on other sites

14 hours ago, Neileg said:

I use lens wipes to clean crystals. Very convenient and better than any other fabric/liquid combination.

i've not had a problem with dust but cat hairs are a different matter!

Neil

But make sure the wipes don't contain isopropanol if it's an acrylic crystal.

Link to comment
Share on other sites

4 hours ago, mikepilk said:

But make sure the wipes don't contain isopropanol if it's an acrylic crystal.

Mmm...

The ones I use are for spectacles. So far as my research shows in the UK at least, all contain denatured alcohol and water. 

Thanks for the heads up.

Neil 

Link to comment
Share on other sites

I have a box of Zeiss lens wipes next to me here - says on the back isopropanol and ethanol.

IPA causes micro cracks and makes it go misty - I discovered that the hard way.

I just looked it up, and it seems that ethyl alcohol is ok with acrylic. It just depends what the 'denatured alcohol' is.

Mike

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • 1947 NOS Ambassador 'C'. Actually, the case came without the movement so the movement isn't NOS, but she sure is pretty.
    • Hi attached is the AS 20XX. Service sheet although there is no 2063 mentioned it may be of some use to you AS_AS 2060,1,2,6,4,6.pdf
    • one of the problems we have is visible versus invisible. For instance millennium disulfide another high pressure lubricant black in color. I was told by somebody worked for the Boeing company that they had a piston like device somewhere that has eight call it around it to grab it so it has to slide and in the collet has to grab. But if somebody puts that type of dry grease on where grease with that in it it embeds itself basically in the metal and they have to throw the whole part away they get use it all. So I suspect on all the dry powdery lubricants that they will go into all the basically microscopic cracks and crannies of the metaland that's where it is visually at least until you scrub it off your visually going to see it which is good because you want your lubrication the stay word is. But I'm sure it doesn't last forever on the metal it's just a really nice lubrication  
    • Thanks for the info. I can't seem to find tech sheets for those either.  I'll muddle my way though 🙂
    • Ohh spooky I have just aquired the same one mike, but mine has a drill bit inside it.
×
×
  • Create New...