Jump to content

The Joy Of Watch Repair

joelcarvajal
 Share

Recommended Posts

joelcarvajal Watch Enthusiast

joelcarvajal

Posted
Posted

Which of the following gives you the most ecstatic feeling? [emoji23]

o "One more turn and it's all in!" - winding the mainspring into the barrel by hand

o "Fourth wheel in... Third wheel in... Escapement wheel in... And they are all turning freely! Wee!" - aligning the train gears into their jewels

o "swing please... Swing please... Yes!" - installing and seeing the balance assembly swing into action

o "0s/day...0.0ms...270 degrees... Straight line... Not bad!" - after regulating the watch

o "Such a pretty watch!" - admiring the assembled watch head without strap on wrist while still wearing finger cots

o "You know what? I fixed this myself!" - telling your wife/children/friend your new hobby

o "I can watch all these videos all day!" - gets popcorn and sit in front of the computer to watch Mark's videos

  • Like 2
Link to comment
Share on other sites
anilv Distinguished Member

anilv

Posted
Posted

Best feeling...

'the click as the last pivot falls into place'

 

Worst feeling...

'the click as you tighten down the train bridge screw (means you've broken a pivot)'

'the 'oooHH sh!t' feeling when the watch you're working on hits your lap on the way to the floor'

 

 

Anil

  • Like 2
Link to comment
Share on other sites
frenchie Distinguished Member

frenchie

Posted
Posted

Balance in and instant start for me! :)

Same for me !

Nothing is more depressing than doing all the dis-assembly, getting the parts fixed and cleaned, putting it all together and when the balance goes in, nothing happens...

  • Like 1
Link to comment
Share on other sites
SteveFitzwater Member

SteveFitzwater

Posted
Posted

I would have to go with when you drop that balance in and it comes to life on its own..

 

the worst is finishing up a restored watch and as you rubbing off something on the train bridge with some rodico and your thumb hits the balance and you here a click and realized you just broke your balance staff... I walked away from my shop for a few days after that one..

  • Like 4
Link to comment
Share on other sites
MrBeat WRT Addict

MrBeat

Posted
Posted

Balance in and instant start for me! :)

 

Id have to agree with Geo, that is always a guilty pleasure for me.

 

Personally for me its discipline of patience, patience , and more patience. Perfecting each stage and giving my very best efforts & concentration into each part. Hand polishing alone can take days or even weeks, but results are worth it.

  • Like 2
Link to comment
Share on other sites
joelcarvajal Watch Enthusiast

joelcarvajal

Posted
  • Author
Posted

Id have to agree with Geo, that is always a guilty pleasure for me.

Personally for me its discipline of patience, patience , and more patience. Perfecting each stage and giving my very best efforts & concentration into each part. Hand polishing alone can take days or even weeks, but results are worth it.

I agree! And I should have added that aspect of watch repair. At this stage of acquiring skills, I tend to focus on servicing the movement. But I guess knowing how to handle crystals, watch cases are just as important... And satisfying!
  • Like 1
Link to comment
Share on other sites
joelcarvajal Watch Enthusiast

joelcarvajal

Posted
  • Author
Posted

First swing of the balance has to be right up there, but what about that feeling when you finally track down that elusive part after 3 hours on the Internet?

S

I know the feeling! I once had a need for several parts of a movement but had a hard time finding all of them, not to mention the cost has between piling up. But when I saw someone selling the same movement albeit not working and for repair, I gambled and grabbed the item. With my fingers crossed I waited for the movement to arrive, hoping at least the parts I needed are in good condition. Fortunately, the gamble paid off! Happiness!
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

For me finding the reason for a fault & fixing that fault.  A real sense of achievement :woohoo-jumping-smiley-emoticon:

When a customer would say I've had this watch or clock repaired, I've taken it back many times and it still doesn't work. When you repair the fault and knowing it is going to be satisfactory. That would be one of my best feelings, because you know next time the person wants something repaired there more likely to bring it to you then to take it elsewhere. 

  • Like 1
Link to comment
Share on other sites
  • 2 weeks later...
steven WRT Addict

steven

Posted
Posted

For me finding the reason for a fault & fixing that fault. A real sense of achievement :woohoo-jumping-smiley-emoticon:

That's me too. And when the reading on the timegrapher is perfect after fine tuning the hairspring.

Sent from my iPad using Tapatalk

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      This makes much more sense now, the oil is withdrawing itself to make as little contact with the epilame as possible. Same principle as wax on a car creates a hyrophobic surface that makes the cohesive properties of water molecules pull together.  The water beads run off only when under the influence of gravity but still remain cohesively beaded up. And as mentioned earlier a pivot would keep the oil in place on a cap jewel.  Epilame on an escapement would be a different scenario, there is nothing to hold the oil in position if gravity tugs at the bead to move, plus the escape teeth pull the oil about Maybe this is why its suggested to run the watch for a short while to remove the epilame to make two oleophobic surfaces either side of the oil, creating a ring of fire 🔥 around it 😅
    • mikepilk
      Balance wheelwheel crooked

      By mikepilk · Posted

      As with every skill it watchmaking, it takes practice. Notice at the top of the document it says, "Practical work - 40 hours".  I can get the balance wheels 'close enough' to flat, but never seem to get them perfect. Same with gear wheels. Guess I need more practice.
    • transporter
      Beat adjustment

      By transporter · Posted

      Has it got a beat adjustment on the platform or is it a fixed hairspring? in short what you are looking at to get it just about in beat is to get the roller jewel sitting dead centre between the banking pins. So remove the platform and take of the pallet fork and escape wheel to give you clear line of site, sit the platform with the balance in place and with it level look between the banking pins and see if the roller jewel is sitting between them, if it is nice and central its there or there abouts in beat, if its not the the position of the pinned end of the hairspring needs to be adjusted to move the roller jewel into the correct position, thats why I asked if it has an adjustment on the platform or not, if it has its an easier job. 
    • MapleWood
      Help - London Elliott Mantle Clock Night Silence

      By MapleWood · Posted

      I've managed to adjust it. I'm going to try and explain it as well as I can with my limited horology knowledge but I hope it helps someone in the future. There is a cam to the right of the front plate as shown in the picture. As the clock ticks along, the pin indicated in the gear comes around and slots into one of the silencer cam gaps, turning the cam. The pin completes a full rotation in 2 hours. To adjust the cam to start at the right time set the clock to just before 7. I did 6:45. Then I turned the silencer cam anticlockwise, which spins freely, until it pushed the silencer lever up and was placed just before the drop. Just before the 7AM indicated in the picture. All I then had to do was progress the hands to 7-7:15which made the pin slot into the silencer cam gap and turn the cam so the lever comes down again, unsilencing the clock. That was it. If anyone comes across this issue again I'd be happy to assist. Thanks again to everyone that helped. Hey Transporter! Thanks a lot for the reply. That was a really good explanation and I'm sure it would have made my troubleshooting a lot less painful haha. I'm sure someone will find it useful in the future. Thank you again for taking the time to try and help me out with this.
    • Waggy
      Epilame / Fixodrop

      By Waggy · Posted

      Now I'm completely confused, it would appear that the epilame  is oleophobic  as @Marc states: This oleophobic  behavior can be seen as beading of the droplet (as above) which stops the oil spreading which is supported by what we observe on treated/untreated cap stones (for example), but as @VWatchie states this should make the drops more mobile and is supported by the literature:   A review on control of droplet motion based on wettability modulation principles design strategies recent progress and applications.pdf   However the hole point is that we have less mobile oil so an oleophobic  would see to be the opposite of what we want. In fact this beading and high mobility are desirable properties in things like smart phone covers, see below.  I am fairly sure that epilame doesn't make the droplets more mobile, so maybe its a strange coating with dual properties that are both oleophobic (beading) and cohesive/adhesive resulting in low mobility?? This may explain the high price??  
×
×
  • Create New...