Jump to content

Recommended Posts

Posted

I've just returned from a trip to Spain, while I was there I went to one of those Spanish village markets, usual stuff, then I came across a table full of fake watches so I bought one just to have a look ( hope I'm not going to be banned from the forum for committing such an act !  :judge:  :ph34r: ) 

The chap was asking 15 Euros but I bartered and got it for 10 Euros, ( about 8 quid )

with no date window & spelling mistake' it says on the dial ''suberlative chronometer''.

 

Slightly worryingly, later on I went for lunch with my other half & her sister, they both said they wouldn't have known the difference between that and a real one ! 

 

Phil.

post-31-0-21237500-1413806289_thumb.jpg

Posted

Tut tut - bad boy! In your bed! :D

Have you got a pic of the "suberlative" movement - just out of curiosity?

Posted (edited)

Hi Phil,

 

As Will said, it would be interesting to see what is inside.

 

Some of them movements are even Swiss, but I guess you'll find mostly Chinese inside. My first move will be to open the watch and check that all gaskets are good and add some silicon grease sealant to both the back and the crown gasket/tube. I would even go to the extent to seal the crystal by carefully adding special transparent crystal glue to the edges where it fits. In my experience -- with some of those I've come across, I don't own any -- is that their watertight properties are iffy at best. Even sweat can get inside, some will fog the crystal in no time at all even in storage by permeating the natural humidity of the room.

 

The printing mistake may give it away immediately but, who will really notice that?! For MOST people, that's a real Rolex!

 

Me, being as I am with watches, I see it as a nice watch that may need a little elbow grease to preserve it and help it last. Nowadays, even the cheapest Chinese movements are greatly improved so you may be able to enjoy the watch for some time to come...and if not, it is only little money!

 

As an after thought, I would service it completely right away just in case. Most of them are assembled in a rather careless environment.
 

Edited by bobm12
  • Like 1
Posted

I think "suberlative" might be the opposite of "superlative", or maybe that's just "sublative" since "sub" is the opposite of "super". Is it a "Suberlative Supmariner"? :)

 

Also notice that your "Oyster Perpetual Date" has no date window. :)

Posted

But it does have a window! Only it is closed, remember "Oyster" like in clam....It is a safety measure to avoid water in!

Posted

Obvious fake is obvious. Its only people who don't know the real thing that fall for it.

Most use cheap poor quality Chinese automatics, the 'good' ones use copies of ETAs.

Personally I'm surprised by the attitude here, fakes have no place are poor quality and do nothing for watchmaking.

Posted

Personally I'm surprised by the attitude here, fakes have no place are poor quality and do nothing for watchmaking.

 

I think we're all quite aware of the crap nature of fakes - hence the slightly amused posts above. Some watch forums even go so far as to ban any discussion of fakes, which I think is stupid, and doesn't make them go away.

 

I've never actually seen a fake watch in my life, to the best of my knowledge, and would never buy one - see what I think about them at: http://www.willswatchpages.com/fake-and-replica-watches.html - but, in a perverse way, to know more about what makes a fake a fake is adding to the sum of watch knowledge! Fakes, as you say, do nothing for watchmaking, but the collector should learn to know what to look for, and not all fakes are obvious to the novice.

  • Like 2
Posted

But it does have a window! Only it is closed, remember "Oyster" like in clam....It is a safety measure to avoid water in!

Well spotted Bob !  

 

this is the model with the ''suberlative watertight date window'', you just have to ask the date and it will tell you.  :lolu:

post-31-0-72222000-1413981465_thumb.jpg

Posted

This is the model with the ''suberlative watertight date window'', you just have to ask the date and it will tell you.  :lolu:

Oh, I just don't know how you can sleep at night! :-)

Posted

Some watch forums even go so far as to ban any discussion of fakes, which I think is stupid, and doesn't make them go away.

 

Agreed. But assuming you're talking about WatchUSeek, I think the intent is to stop discussion about how to obtain fakes, etc.  I see many discussions there, with pictures, about how to tell if a watch is fake, is my watch fake?, etc.  In other words, discussing fakes for the purpose of avoiding them is perfectly allowed, but I'm afraid this thread here would be deleted on that forum.

Posted

Agreed. But assuming you're talking about WatchUSeek, I think the intent is to stop discussion about how to obtain fakes, etc. I see many discussions there, with pictures, about how to tell if a watch is fake, is my watch fake?, etc. In other words, discussing fakes for the purpose of avoiding them is perfectly allowed, but I'm afraid this thread here would be deleted on that forum.

A lot more will be deleted now that they have sold it.....
Posted

A lot more will be deleted now that they have sold it.....

 

I doubt it. The buyers bought it for the ad revenue. They're not going to do anything to drive people away. There was a lot of fear mongering going on over there, although it seems to have quieted down a bit.

Posted

So, in short, this thread basically teach us all what to look for in fake watches so we can IDENTIFY them... Which IMHO, I believe does contribute to watchmaking.

 

Also, the light spirit of the thread basically tells that not only we are learning but we are having fun while doing it and enjoying the sharing among good, knowledgeable and friendly people we appreciate.

 

And last but not least, the watch itself is not a culprit, -- the same way it is not our fault to be born -- but the people that brought them to light are. Therefore, I'll treat those unfortunate watches with respect and simply bear their presence which in a way enhance -- even "advertise for free" -- the value of the ones they copy. ( Otherwise, they would not exist at all! )

 

Just my respectful two cents!

  • Like 2
Posted

Making a comparison between the two pictures it is -- summarily-- evident that:

 

The hands of the good Rolexes are different (check out the straight portion of the "Mercedes" hour hands).

The seconds hand needs a longer tip (fake). 

If the watch had no typographical errors, the window that was noted before and a Cyclops would be in order. Otherwise no "date" should be written on the dial.

The "peep" on the bezel is too big and different type (fake).

The font is different on dial and bezel both in shape and size depending.

I would assume the Rolex logo (crown) is etched differently, and the metal band is also very different not only itself but where it meets the watch head. (some fakes include serial numbers/markings on the links like a real Rolex.

No Swiss on fake dial. Some fakes has this "Swiss or Swiss Made" sign under the seconds track which is not allowed by Switzerland's laws I believe.

 

All in all, many small details FOR THE TRAINED EYE, not for many of us, including me!

 

From the above sentence, IMHO, this fake is well copied (maybe not tops), but for the price it was "well made" if we can put it that way. (can't find a better word than "made"). The absence of "Swiss" trademark might have to do with liabilities both to the wearer and the seller...who knows.

 

I dare you guys to keep finding differences! :)

Posted

The absence of the Swiss trademark has nothing to do with liabilities. The people who churn out these fakes don't care about that.

 

They'd be in just as much trouble for copying the Rolex logo as they would be for claiming their watch was Swiss, but since they're never going to be caught, who cares. And they certainly don't care about whether or not the buyer gets in trouble.

 

One of the reasons that Rolexes are so easy to fake is that there are so many variations. The typo is a give-away obviously, but the fonts can vary enormously between various releases of the genuine article, as can the precise shapes of the hands. One needs to be a real expert to know which shaped parts were actually used together. And there are date Rolexes with no cyclops.

 

Some more things that do give it away are that it's too shiny (a real sub has a brushed finish on the tops of the lugs), the bracelet doesn't fit between the lugs very well (too narrow), the bracelet is "inside out" (brushed centre links and shiny outside ones), and the borders of the rectangular and triangular indices aren't uniformly wide all the way around (I suspect the lume is just stickers that weren't very carefully centred).

 

PS. I'm not a Rolex expert, nor do I own a Rolex, but I've picked up a few things in my two years hanging out in the watch fora.

Posted (edited)

Well spotted, those borders, svorkoetter! Yes, I guess liability doesn't have to do with anything in this market!

 

Oh I forgot, the watch is not claiming to be a Deepsea or a Seadweller so cyclops is necessary here.

Edited by bobm12
Posted

As an afterthought, I wonder why Rolex have any need to use the word "superlative" on their dial in any case? A bit unnecessary, I would have thought - given that Rolex has such a reputation in the world of watches. Down here in Sussex we'd call that having your head up your **BLEEP** - but that's 'cos we're just rude mechanicals down here... :crazysmile:

Posted

That wording is from the 50s, when slogans were more flowery than they are now. These days, it would probably be, "Literally Weirdly Accurate Chronometer". :)

Posted (edited)

The watch world--or any area where replication,imitation, duplication, or emulation can be profitable is interested in noting the differences inherent in forgery, faker, counterfeiting, etc. Once the differences are known, that is where the interets ends. There is no point in discussing these watches--which are REAL watches by the way, just not real Omega, Rolex, Breitling, Audemar, etc, etc.

 

Ten lashes with a rodico cat-o-nine tail for atimegoneby for starting such a topic of anathema. Next case.

 

JC

Edited by noirrac1j
  • 1 year later...
Posted

Evening all,

I just thought I'd add this to an old thread, the fake Rolex I bought in Spain for 10 Euros in 2014 has only recently stopped !

I left it until it stopped before I opened it up, here's what I found....:biggrin: 

WP_20160703_21_06_40_Pro.jpg

  • Like 1
Posted

Not everyone has thousands of pounds to spend on a watch anyway. It's a bit dubious where the revenue goes with these watches but now you've bought it don't forget the most important thing, ENJOY IT. As stated much can be done to rectify any defects and who knows, you may even be able to jump in the water and go swimming with it. More than most genuine Rolexes ever do I suspect.

Sent from my SM-G920F using Tapatalk

Posted
Not everyone has thousands of pounds to spend on a watch anyway. It's a bit dubious where the revenue goes with these watches but now you've bought it don't forget the most important thing, ENJOY IT. >

There is no need to spend thousands of pounds to enjoy a fine watch. Many cost just tens and are lovely. I do not see how a watch lover can "enjoy" wearing a counterfeit piece made to deceive and project an inflated image of oneself. Ok for a prank at most.

  • Like 1
Guest
This topic is now closed to further replies.

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Thanks for this post MikePilk, I just came across a similar problem with an Omega 1022.  The problem I had was the seconds pinion spring was bent out of shape and did not even engage with the wheel properly, so the seconds hand was not moving at all. (no power loss though :) I removed the automatic module so I could access the spring and work on it. Once I bent it back close to the right shape, I experienced the same problem you reported about power loss.  Many tweaks later, and the seconds hand is moving properly again, with amplitude back to good numbers again. Cheers
    • After cleaning up the pivots, I made bushes on the lathe. At this point I've pressed in 6 bushes (3 sets) and the wheels turn smooth. What I can also tell you, is that I'm not looking forward to final assembly. Getting the pivots aligned seems to get exponentially more difficult with each wheel that is added.
    • Islands are interesting places to live depending upon their size and other factors. This is a bigger island and it has a bridge to get there at least on one end. It's also big enough that you don't have to go someplace else to get things typically. It can be a problem if you get a job in Seattle though. Yes I've known of people who commuted from the island to Seattle for a job and I don't quite remember how many hours it took but it took a long time. So basically islands are nice if you don't have to leave very often.
    • Thanks @JohnR725! Everything you say makes a lot of sense and is encouraging to read.
    • isn't it nice to have a decent case open or when the case doesn't want to be opened? In the case of a Rolex watch that supposed to pass specific water resistant testing you probably do need to tighten the back down. But they shouldn't be tightened so much that they risk stripping the threads out. Then the other problem that comes up is the gaskets can start to disintegrate and then getting the back off can be quite a challenge unless you have a really good tool and perhaps some penetrating oil to loosen things up. Yes really nice case marking. When I was in school we were taught to mark the cases and  the American watch and clockmakers Institute even had a? So if you joined at one time they would give you an identification number. They were explaining or giving an example of if the watches ever found in you have a unique number they can perhaps figure out the history of the watch or identify the body it's attached to for instance not that that probably comes up that often. So you got a unique number and even made a special metal stamp that you can purchase. It wasn't a super big aggressive stamp but still it left a mark in the back of the case. Then I heard from people at work on Rolex watches they were using a felt pen indelible but later on they decided that was bad because apparently the ink could release  chemicals although it seems like once it's dry that shouldn't be an issue. Then of course today was nice is you can keep computer records sealed have to mark anything at all I personally find it's best to leave no reference behind that you were even there. Especially when you have a beautiful watch that has no markings at all and now it has your scribbling all over it not good typically if there is a typical and watch repair?  a lot of minor repairs you don't need to do a complete servicing. But beyond a certain point you're going to have to take apart a lot of stuff you're going to disrupt the lubrication even if it looks perfect right now and yes you might as well just go ahead the service the whole thing. also in a watch like this where a lot of things seem to be going on the complete service would be better then you'll know exactly where you stand versus dealing with unknown mysteries for prior repair.
×
×
  • Create New...