Jump to content

Recommended Posts

Can anyone tell me what these cards are?  They are from a watchmakers shop. I bought them just as a record of an era when physical files had to be kept.   Thank you in advance  





Link to post
Share on other sites

My guess is that they are parts interchangeability data for ETA movements, detailing part numbers and all of the different calibres that each part fits.

Potentially still a very useful resource today.

Link to post
Share on other sites

I am wondering if maybe these were supposed to be in a material house versus watchmaker shop. For those of us that were lucky enough to experience going to a physical material house a lot of their reference material was on cards.

  • Like 1
Link to post
Share on other sites
1 hour ago, JohnR725 said:

I am wondering if maybe these were supposed to be in a material house versus watchmaker shop. For those of us that were lucky enough to experience going to a physical material house a lot of their reference material was on cards.

Agree,  with in/out records to keep track of inventory.. over years or decades!

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By MyFavoriteObsession
      I picked the up the 1945 Bulova Cadet as a non-worker on eBay, then I received a parts lot that had a Westfield case and dial. Of course, I had to get a 1940 Westfield Trojan cousin movement for it. 

      Unfortunately, I didn't notice til this morning that the replacement Westfield had a curved dial whereas my case had a flat dial and it doesn't fit. Oh well, guess I'll have to buy more watches. 
    • By RJC87
      Hi guys! I have a watch that uses a Ronda 751 quartz movement (see pic). For those unfamiliar, it’s a small tonneau shaped movement - usually a woman’s size (5½ x 6¾ linge and 2.5mm thick) with the following specs:
      Linge Size: 5½ x 6¾, 2.50mm thick
      Hand Size: 120/70
      Stem: 401-1237
      Cell/Battery/Power Source: 379
      Tap Size: 10   I’d like to replace it with a mechanical movement: I started off looking for a direct drop in replacement but it’s proved very difficult. I haven’t found any modern movements with the same dimensions (although to be fair I haven’t had much luck finding a comprehensive listing of modern movements available). As far as the vintage movements go, (from here: http://www.ranfft.de/cgi-bin/bidfun-db.cgi?10&ranfft&0&2uswk) the ETA 2480 (http://www.ranfft.de/cgi-bin/bidfun-db.cgi?10&ranfft&0&2uswk&ETA_2482) is a good example of the vast majority of what’s available— the right dimensions but 1mm too thick. And for a 2.5mm movement, 1mm is a ton.    The Tissot 530 (http://www.ranfft.de/cgi-bin/bidfun-db.cgi?10&ranfft&0&2uswk&Tissot_530), and Enicar 672/678 (http://www.ranfft.de/cgi-bin/bidfun-db.cgi?10&ranfft&0&2uswk&Enicar_672) are the 2 that seem closest but they are still a half mil too thick. And worse, even if it fits, where would I even begin looking for one?   Does anyone one have any knowledge of a movement that would work or one I could modify a bit to fit? Or any idea the best place to look??   Thanks in advance for the help and I love the forum!!
    • By toptime810
      Can someone tell me the millimeter distance between the two registers on a Venus 175 movement? I am trying to find out if my movement will fit a Venus 175 dial.
    • By FL
      I need assistance, please!
      I have a Pierre Cardin dress watch without a battery/cell and has no numerical identification anywhere in, or on the case. The only ID type info is as follows: it says "Jour" on the inside of the case-back. On the movement is says "Le Jour" with no other wording or numbering. The questions are: What battery/cell would this movement use? and, What movement might this be? Replacement movement? I have tried to research this to no avail.

      Then, can anyone suggest a replacement movement for a Timex Electric M cell; once again no case numbers. However, the inside of the case-back has "QTO" factory marking stamp. Additionally, on the movement itself it has a "04" at approximately the 7 position and a "126" at approximately the 2 position.

      Any help is greatly appreciated.

    • By canthus
      Came across this whilst trawling for info.  Seem to have a large selection of decent watch cases,movements etc.  Not used but may be helpful to others searching for that obscure item.  In Italian so you may need a translator app.
  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • out of curiosity is this your first watch to service? then just to be clear does your watch look like they watch in the picture at the link below? if so you should look carefully and notice that will have to taken apart if you really want to oil the pivots. That's because the two pivots that are visible have cap jewels which prevent you from putting oil on them. were going to have to disassemble if you really want to lubricate. But I would probably do some diagnostics first like when the battery is in and you listen to the watch can you hear anything like a humming sound from the tuning fork that is assuming it is like the watch below?. https://calibercorner.com/omega-caliber-1250/  
    • Thank you for your introduction and welcome to this friendly forum. Why not sign up to Mark's first course and get to know the basic.
    • The lume binder holds the new pip in place. 
    • Manufacturing Seiko lume pip for 6309 7040. Using a staking set and peice of plastic from bergeon packaging which is the right thickness, once in the bezel I will relume with c3 and post more photos 
    • I made a habit of putting just balance cock assembly on mainplate( nothing else) to examine and make adjustments before the clean, namely to check how balance spins in several positions and level the coil, check its concentercity, make sure nothing rubs and pivot shoulder stand proud of jewels and the jewel housing,  next you want to add the fork on and check fork&roller table and guard pin, so would be the end shake most observable When there is no other part on mainplate but balance cock assembly, you have most access to the balance complete nearly from all angles around it, better sight form each view and damaging gears in case driver slips.  I strongly recommend practicing removal and re installation of cock&balance assemby on a cheap scrap till you master the task. As for mainspring power, gently encourage the power, push to turn the barrel that is supply additional torque to it and observe.  All the best. joe
  • Create New...