Jump to content

Recommended Posts

Posted

Completed the watch today. Seiko Sportsmatic 411, 7005-8016P, lemon dial, eBay find, originally bought in 1971 in Singapore with original guarantee card, no web sales back then. Fully serviced and running very well. Very happy

IMG_20210101_142125353.jpg

IMG_20210101_142054553.jpg

IMG_20210101_141316306.jpg

  • Like 5
Posted

1087083567_IMG_E06891.thumb.JPG.758d32e4ef391c9d8da74b728db9eb16.JPG

Recently acquired this junker. But I quite like it, so I'm going to fix it up and enjoy it.

Faux Eta 2824 inside is running fast, and presumed dry. I regulated it down to +10 (and put put a drop of oil on the dry rotor bearing so it was less noisy than my snow blower) and will either service it or replace it. Looks reasonably close to the real one, which I did try on when it was available. This is about $10, 250.00 less expensive than that one was, so I have a bit of change to cover lubricants...

  • Like 1
Posted
6 hours ago, Tudor said:

1087083567_IMG_E06891.thumb.JPG.758d32e4ef391c9d8da74b728db9eb16.JPG

Recently acquired this junker. But I quite like it, so I'm going to fix it up and enjoy it.

Faux Eta 2824 inside is running fast, and presumed dry. I regulated it down to +10 (and put put a drop of oil on the dry rotor bearing so it was less noisy than my snow blower) and will either service it or replace it. Looks reasonably close to the real one, which I did try on when it was available. This is about $10, 250.00 less expensive than that one was, so I have a bit of change to cover lubricants...

How do you open these? Just like the real one? I got two of them, wanted to give them to my almost 6 years old daughter who likes to play watchmaking game, but could  not open them. She sits in my chair, I am the customer and she works on my watches for £1, IF she is open and not tired. What surprised me that i was also charged 50p for my coffee. ? 

  • Like 2
  • Haha 1
Posted
8 hours ago, Tudor said:

1087083567_IMG_E06891.thumb.JPG.758d32e4ef391c9d8da74b728db9eb16.JPG

Recently acquired this junker. But I quite like it, so I'm going to fix it up and enjoy it.

Faux Eta 2824 inside is running fast, and presumed dry. I regulated it down to +10 (and put put a drop of oil on the dry rotor bearing so it was less noisy than my snow blower) and will either service it or replace it. Looks reasonably close to the real one, which I did try on when it was available. This is about $10, 250.00 less expensive than that one was, so I have a bit of change to cover lubricants...

This watch has something in common with the real one - both are hard to open? ?

 

R - Copy.PNG

Posted (edited)

Not hard to open, with the right tools. 

Surprisingly, it is shower-proof. 

I’ll put on a proper 7030 tube and 704 crown for insurance. But it’s a nice knock-around watch to keep my nice ones, nice. 
 

To answer the question prior, that I missed, it uses the same die as a regular sub- 1680, 16610, and I assume the 116610 as well. This is an 116600 sea-dweller. The “deep sea sea-dweller” with the hoky “ring lock system” uses a larger die, which came in my set (and remains unused). The Tudor 9411 uses the size smaller, which I think also fits the datejust. 

Edited by Tudor
Posted (edited)

A black dialled Swatch Irony today.

RIMG0206.thumb.JPG.5d9ff976230126f229b8950be8f77aae.JPG
This is another design classic, and also a bit of a Marmite watch. Either you love it or you hate it. I'm a big Marmite fan myself.

Closeup2.thumb.JPG.efef3ec9e068019e3f2e842680de512d.JPG

Closeup.thumb.JPG.4a3d24d9ee30d25352cb9e7cb26a2d59.JPG

RIMG0201.thumb.JPG.44c7117dadfe591fd970327f42700c1b.JPG

The only thing that lets it down in my opinion is the lume. Yes, the hands are nice and bright, but there is absolutely nothing else on the dail or case that is lumed, so it may well be sitting glowing gently on the bedside table next to you as you stare at it bleary eyed, but unless you reach out and grab it to figure out which way up it is, you have absolutely no idea what time it is. Even with it in your hand, you only have a vague idea.. 3am, maybe, or is it four.. who cares, its too early I'm going back to sleep.

Edited by AndyHull
  • Like 2
Posted (edited)
On 12/10/2018 at 9:25 AM, AndyHull said:

When I get back from my holidays, I'll order up a crystal for it.

RIMG0213.thumb.JPG.b75777580914059b7c9413b042ea5642.JPG

Well I guess I forgot to order a crystal for it, partly because it has one of the most ravenous arm hair eating band I've ever encountered, which kind of spoils the fun of wearing it. The monster hair puller is the original Seiko steel strap I might add. 

RIMG0217.thumb.JPG.0d4a852b21e655d4a252baca67c98dc4.JPG

However it is a classic Sekio 5 design (from 1981), and it seems a waste to have it just sitting around unworn, so I put a leather strap on it and I'll measure the crystal this evening and order one... probably.. if I don't get distracted by something else. 

Who knows, I might even have a crystal in stock, and be able to strike another ancient item from the todo list. 

Edited by AndyHull
  • Like 2
Posted (edited)

RIMG0221.thumb.JPG.5b0c3162532cb96628c20ebdbdc91f2b.JPG

Rather surprisingly I did have the correct crystal in my stash.
I think that looks a whole lot better don't you?
One more item removed from the to do list.

RIMG0222.JPG

Edited by AndyHull
  • Like 2
Posted

Here is another watch found in my dad's collection of abandoned watches.  When I discovered it, I saw that it would run fine but lost tons of time.  After dusting off my brain and recalling what my dad taught me and with a little help from the internet, I set about to tighten the canon pinion.  Whoooo...very scary, but I seem to have been successful.  It keeps great time.  After polishing the crystal, it is a real beauty.

2021-01-09 07_52_35-Photos.png

  • Like 4
Posted
8 minutes ago, LittleWatchShop said:

Here is another watch found in my dad's collection of abandoned watches.  When I discovered it, I saw that it would run fine but lost tons of time.  After dusting off my brain and recalling what my dad taught me and with a little help from the internet, I set about to tighten the canon pinion.  Whoooo...very scary, but I seem to have been successful.  It keeps great time.  After polishing the crystal, it is a real beauty.

2021-01-09 07_52_35-Photos.png

You're not wrong, lovely watch.

Posted

RIMG0242.thumb.JPG.9eee1a5dd4abb6d3cc77c16b5f8c4c58.JPG

I stripped and cleaned the 1950s Metamec Electric clock today. It had been lying in "covid quarantine" since its arrival a few days back. 

RIMG0243.thumb.JPG.daf2278dec1751c579eb9bfe7e052bd2.JPG

As well as the missing wooden detail, it also has a slight fault. The original cable was held in place by two recessed grub screws and a cable clamp of some description. The clamp is missing as is one of the grub screws, which is not a huge issue as I can probably replace those with something modern relatively easily.

However the second grub screw is stuck in place and its head has been stripped off, so I will need to figure out whether I want to try to extract it, or fill the holes and make some alternative arrangement to fit the mains flex. I'll probably go for the second option as it will be a lot more secure and less of an electrical safety risk. The idea of recessed live terminals is a little too 1950s for my liking.

RIMG0246.thumb.JPG.b2fe91348919bc5297784477d149cfeb.JPG

The more obvious chips and dings in the finish were touched up with shellac, which will probably need a couple of additional coats with a light sanding between them, and I still need to figure out what to do about the missing left hand wooden edge piece.

Looking at the small remaining  broken piece of it that I have removed, my best guess is that it is oak, so I can either find a bit from the log pile, or maybe take a trip to B&Q and see if they have any hardwood mouldings that could be knocked in to shape and stained. The most tricky part I suspect is not going to be shaping the replacement piece, but colour matching it.

  • Like 3

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I'm sure it's the ancien. My measurements: A = 342. The slight bend in the pivot would make much less than a thousandth of a mm difference to this so I don't think 348 is plausible unless there has been significant wear on the pivots. B is hard to measure without first removing the balance wheel. I measured to the other side of the balance wheel as best I could (263) then subtracted the thickness of the wheel (69) to get 194. This could easily be three or four hundredths out, so 195 looks right. (196 could also be right.) J couldn't be measured. I did my best to measure where the balance wheel has been riveted on and got about 95, so 85 before riveting is plausible. (60 is not.) G again couldn't be measured without first removing the roller. I get 37 where the staff emerges from the roller so 41 at the other end of the taper seems plausible. (43 is also plausible to me.) K = 60. (Definitely larger than 55.)   I've never replaced a balance staff; it'll be a new adventure for me. I'll have to read up on how to maximise my chance of removing the old one without damaging the balance wheel without having access to a lathe. I also need to explore how to remove the roller without damaging it. I won't actually place an order until I've gone through the rest of the movement. With the number of issues I've already found, I'll be amazed if I don't have more surprises in store. There are some watch part suppliers in Australia but nothing like Cousins or Otto Frei or Jules Borel. AllTimeCo is fine for basic parts for modern watches: batteries, bands, some crowns, stems, seals, movements, some tools, etc., but not really anything for vintage watches. Australian Jewellers Supplies is similar. Cousins charges about £9 for shipping to Australia which is about AU$19 and not too bad (considering Australian parcel post is $11) but I still want to minimise the number of times I'm paying it. I need to explore other options closer to home. There may be something in Singapore or China that would have what I want and ship it faster/more economically.  
    • Hi, I just finished the service of a Rolex 3135. Amplitude is great, 295 degrees horizontal after 2 hours and 280 after 12 hours. Vertical positions are 25 degrees down on those. I am however seeing a rate variation with temperature. I have 0 SPD on wrist, say 38 degrees and +7 SPD at 18 degrees room temperature. That equates to +0.35 SPD which is within spec I believe (+-0.5 SPD/ Deg C max). It just seems more than I would expect from such a high quality movement. To put that in context, I see similar rate variation with temperature for a Seiko 7S26. Just wondering what you guys see. Thanks, Steve.
    • For years I've done it the el-cheapo way (read: cleaning by hand). Bought a 2nd Elma S15(H) ultra-sonic, including proper cleaning-fluids (Elma WF Pro (cleaning) & Elma Suprol Pro (rinse)) and entered a complete different cleaning world. These cleaning fluids are none-water based and not that easy to obtain. Initially I bought these fluids in Germany "SKSONIC" (www.sksonic.de) but last year they stopped shipping international. Perhaps they resumed international shipping? You can always ask them. You could also ask @VWatchie, he lives "next-door". As for the fumes; I use the ultra-sonic in my garage, partly for the fumes, but more for our dog ...... he goes "bananas" when I switch on the ultra-sonic. Oh, next on your list (if you consider watch-repair as a long-time hobby), a Microscope (up to 50x is enough).  Pegwood leaves, observed under the microscope that is, whole tree-trunks behind 🫣 Ultra-sonic, in combination with proper cleaning fluids, takes care of the cleaning.
    • How do I remove the hairspring from an ETA? 2846. Balance  staff pivot is broken and I need to transfer the spring over to a new wheel. But the spring stud is not removable. It seems it almost looks like a snap ring at the top of the balance cock or am I missing something?
×
×
  • Create New...