Jump to content

- Look mommy I made a mainspring flower.

B3stia

By B3stia
in Watch Repairs Help & Advice

 Share

Recommended Posts

jdm Distinguished Member

jdm

Posted
Posted
41 minutes ago, vinn3 said:

thumbs are the way to go,  if you are thin skined or  bleed easly;  use leather gloves.  i forgot to mention "acidic hands"  it could be a problem.   vinn

Try not to use thumbs, it's easy. Left hand keeps coils pressed in the barrel with the flat of the tweezers, right hand (with gloves or finger coats) puts in the spring, and the tweezers follows. Let the tool do the hard contact, not your skin.

 

 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted (edited)
2 minutes ago, vinn3 said:

is there a chart somwhere to tell you  which direction YOUR  watch main spring is wound?  IT IS  possible to get it ALL back  together  AND  still not know  WHATS THE HECK WRONG NOW?   vinn

A picture before taking things apart would help I think. And if no picture look at the barrel screw if left of right threaded.

Edited by jdm
Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted

As you can see by this guy winding a spring by hand is not easy. I used to use his method but I had lots of failures. Also notice that he does not wear finger cots & I suspect no lubrication has not been applied to the spring. My advise is to bite the bullet and purchase a spring winder.

Link to comment
Share on other sites
Cad101 Super WRT Addict

Cad101

Posted
Posted

I've put so many mainsprings back by hand I bet I'm not far off the speed of a winder :DI usually get one coil in then press down on top of the spring using alternate thumbs the spring just follows its natural route around the inside its simple when you've done a few.

  • Like 1
Link to comment
Share on other sites
Vich Distinguished Member

Vich

Posted
Posted

I seem to manage watches ok but only the once I wound a carriage clock spring in by hand and required safety goggles one leather glove and one poly glove.  I will have to be backed into a corner to repeat the experience.

there are a few examples of videos using the winders or by hand to learn from but you do need some luck as well and the skill will appear eventually. Don't give up though - speaking as someone who has probably made a hash of numerous different parts of a watch over the time I have been tinkering.

Cheers,

Vic

Link to comment
Share on other sites
MrBeat WRT Addict

MrBeat

Posted
Posted

One method by hand ive not used in years is placing the arbour in place and holding it very firmly with a pin vice from opposing side of barrel, then with the mainspring hole end fitted to the arbour turn the pin vice to wind the spring in whilst using the tip of your left finger to hold in the primary coil ( using a finger cot of course ). Easier to see in practice than explain in writing but im sure you get the principle :) 

And help to have a good range of pin vices :D

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • JohnR725
      Seiko 6601 Tech Sheet?

      By JohnR725 · Posted

      yes I noticed the new site and I miss the old site. It's the unfortunate problem of the Internet here today gone tomorrow sometimes some of the stuff gets backed up and sometimes well it does not then the problem with the early Seiko's were there were not necessarily designed for distribution across the planet and as such there is no customer support for them. So trying to find early stuff like technical information or sometimes even parts list for older Seiko is is problematic. But I did find you a you tube video. A quick look he seems to take a heck of a lot of time to actually get to the service single I did not watch all that but it does look like he did disassemble or started to say there's a tiny bit here  
    • HorologyHead
      An intro…

      By HorologyHead · Posted

      RichardHarris123: Hello and welcome from Leeds, England.  I have family all over Australia, went as £10 poms Thanks Richard. Hope you’re able to visit your family here and that they’ve all done well 🙂 My relatives arrived from England in the 1790s transported on the ‘Second & Third Fleets’—a story of timber sailing ships, of convicts and doing well in this huge Country of Australia. When I visited the UK in the 1980s, I was too young to comprehend the depth and breadth of its history…  Best wishes, Mike William Chapman, my 4th great Grandad’s charges, at age 23 read at the Old Bailey; sentenced to 7 years of transportation to Sydney.
    • Endeavor
      New balance staff not riveting to balance

      By Endeavor · Posted

      The whole process and the progress are closely observed, it's hand-driven and very controlled. I can't see the "danger", unless you are watching the TV while doing it. As you could have read, and in this quote "wheel" is the balance-wheel.
    • Mercurial
      AS2063 - hand setting

      By Mercurial · Posted

      Have you got the pallet fork installed in the movement when you see the train move when using the setting works? As nevenbekriev said, without the pallet fork to lock the train, the behaviour you are describing is normal. If this is happening with the pallet fork installed, you have a problem in the gear train, it should be immobile when the pallet fork is locking the escape wheel.  The fit of the circlip above the pinions on that wheel is crooked in your pictures, it should sit flat up against the upper pinion as in Marc’s picture.  Hope that helps, Mark
    • Khan
      Stem broken - can it be rescued?

      By Khan · Posted

      Hi I got a Jaeger LeCoultre K911 movement, where one of the stems was broken. Part no. Should be 401.  Im based in Europe and tried Cousins but its discontinued. They except to get stem in stock for cal. K916 but will that work? Or Is there a way out to join the ends?
×
×
  • Create New...