Jump to content

Pallet Warmer Project


Mark

Recommended Posts

Editing a video on the construction at the moment. 

Need to reset the pallet stones in a vostok which was loaded up with too much shellac. Unfortunately my pallet warmer is missing - searched high and low - I suspect it's in pallet warmer heaven. So I made a new one. Hopefully this will be an interesting video for some. In fact - I made two. Will do a giveaway to a winner for one of them. Details will be announced in my next video which will show how I made these and the video after that will the Vostok restoration where I will demonstrate how they are used.

In the meantime - if anybody wants to build one themselves, I have attached the plans to this post. If you do make one then post pics :)

pallets.jpg

pallet-warmer.jpg

pallet-warmer2.jpg

pallet_warmer_sketch.png

pallet_warmer_sketch2.png

Pallet Warmer Plans.pdf

  • Like 3
Link to comment
Share on other sites

Nice one, thanks for the plans.... Strangely enough I was just looking for mine before reading this and found it.
Maybe your lost one is with Bagpuss?
1996946093_20191111_1252421.thumb.jpg.ca93f72c392349a88ce9b5395c8aa033.jpg
Yikes - bagpuss. Now that's a blast from the past!

Sent from my SM-G950F using Tapatalk

  • Like 1
  • Haha 2
Link to comment
Share on other sites

32 minutes ago, watchweasol said:

Hi  Likewise Old H do you remenber Andy Pandy and Teddy , Watch with Mother,   not forgetting the Interlude....

Watch with Mother Monday

Andy Pandy Tuesdays

Rag Tag and Bobtail Wednesday

Bill and Benn Thursday

The Wooden Tops Friday.  

Link to comment
Share on other sites

A nice video Mark. What type of lathe are you using?
@oldhippy Sorry for late reply.
It's a mini bench lathe made by a company called Optimum. A relatively new addition to the workshop along with the mill.
761cd7f46b1fd130a335b5ee54b960dc.jpgefd09d341be590b70a66549f5ac6e60a.jpg

Sent from my SM-G950F using Tapatalk

Link to comment
Share on other sites

1 hour ago, TheFixer said:

I have the copper plate so just need some brass.

Any chance of a picture with the wooden holder without the tool itself?

You can see it clearly in the video Mark uploaded, he shows the machining out process but it could be easily done with a chisel or by tacking sides onto a flat piece.

  • Like 1
Link to comment
Share on other sites

On 11/15/2019 at 10:59 PM, oldhippy said:

Thank's Mark for the reply and nice photo. That's a new one on me I'll look that one up. 

Is it the Light Duty Lathe Optimum TU2004V 240v Variable Speed?

Absolutely - thats the one. So far I have had a few issues with it but noting major.

The gib in the compound slide was bent - easy fix but I need maybe add a couple more gib screws to make it more smooth and it came with an extraordinary amount of grit on the lead screws and ways. This is common with chinese lathes I think but didn't expect it with "German quality" - lesson learned :D

I would like to install a thrust bearing too, to minimise  backlash. But the parts I have made so far are quite accurate not bad for a light duty lathe. Not unhappy.

 

13 hours ago, TheFixer said:
I have the copper plate so just need some brass.
Any chance of a picture with the wooden holder without the tool itself?

There you go9fd5114a1d5f9cd0f0957a0133eaa82d.jpg

Sent from my SM-G950F using Tapatalk
 

Link to comment
Share on other sites

8 hours ago, Mark said:

Absolutely - thats the one. So far I have had a few issues with it but noting major.

The gib in the compound slide was bent - easy fix but I need maybe add a couple more gib screws to make it more smooth and it came with an extraordinary amount of grit on the lead screws and ways. This is common with chinese lathes I think but didn't expect it with "German quality" - lesson learned :D

I would like to install a thrust bearing too, to minimise  backlash. But the parts I have made so far are quite accurate not bad for a light duty lathe. Not unhappy.

 

There you go9fd5114a1d5f9cd0f0957a0133eaa82d.jpg

Sent from my SM-G950F using Tapatalk
 

Thank you Mark that is very helpful.

Link to comment
Share on other sites

  • 4 weeks later...


  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hello from the Mid-Atlantic United States. I've been in the hobby for a few months and have concluded that I will be staying in it for a while. I've started to get some proper tools and I am looking forward to developing some skills. My current goal is to get comfortable enough to service / repair some watches I've inherited from family members.  My current project is a Mentor pendent watch with a BF866 movement that belonged to my great aunt.
    • Success! The watch is working, albeit not perfectly. I need to install a new mainspring. It only runs about 16 hours. Still, it's my first cleaning and rebuild. I bought it from the original owner's son on eBay! The other one was bought at a flea market. I needed both to complete the project. The model with a seconds hand had soldered watch band pins and I couldn't drill tiny holes so I used the flea market Waldan, which was nearly a perfect match. I also replated the case with nickel, but the result was subpar. It's never as easy as it looks.
    • Thanks guys. It's a Seawolf 10ATM pre spring bezel. The case knife stressed me a bit, but eventually got it off and cleaned - nearly seventy years of grime.  Thanks.  Cheers John
    • Exactly. This is a pic of the hairspring I'm working on. My horizontal v vertical rates are all over the place. There is no discernible terminal curve. My problem is that the outer coil is (possibly) hitting the regulator pin. It's hard to tell but it looks to be getting very close. Also getting close to the stud, which could be @VWatchie's problem. You can see that I need to adjust the inner coil to centre the collet. That will hopefully solve the problem. But then I'll take the spring off and attach it to the cock to see how it looks.   I don't know if it's causing your problem @VWatchie, but I would say your inner coil looks like this  
    • Welcome to the forum.
×
×
  • Create New...