Jump to content

Which Watch Have You Got Coming In The Mail ? Show Us !!!


SCOTTY

Recommended Posts

you might see a theme developing here.

the blue dial is already here, but the front office at my apartment complex has been closed from last thursday because of the storm. i'll get it tomorrow.

the other two should be here this week.

post-836-0-50295800-1453680551_thumb.jpg

post-836-0-48006300-1453680567.jpg

post-836-0-29399400-1453680589.jpg

  • Like 1
Link to comment
Share on other sites

God!  I can recall looking at the Bulova watch display that had Accutrons on it back when I was a kid.  I was always peering into the local jeweller's display window while my mum went supermarket shopping.

 

My favourite displays were for the Omega moon watch and the many LANCO and Tissot watches.  Also, there was an Australian company that imported Swiss movements and sometimes cased watches here called "Felicia".  Felicia watches were very good... toughly-made and not all that expensive.  Not much more that the ubiquitous Timex watches that were in all the department stores back then.  Here are two locally-made Felicias I lusted after as a kid:

felicia2s.jpg526051235_tp.jpg

Edited by stroppy
Link to comment
Share on other sites

Both of these watches are project watches from the Chinese Mechanical forum on watchuseek. The GMT is a limited edition, and I don't know what factory either one is made in. I believe the 1963 is generally available right from Ed in Hong Kong. The movement in the 1963 is Seagull, as far as I know. The watch is labeled ST1901.  Ed is very approachable, and I'm sure can answer any questions you have.

 

Have fun!

Link to comment
Share on other sites

I have this Chinese beauty flying to me from my favourite Ebay supplier as I type:

 

HK-post-Jaragar-Men-Gent-Black-Tourbillo

 

 

A nice looking watch stroppy, some of the cheap Chinese watches really look the part and for the price you can't go wrong, I have 6 or 7 mechanical & quartz , most of the quartz have Miyota  movements, and as far as I am concerned the movement is the heart of a watch.

 

If I had the dough I would spring this little looker.  272103922181

 

Max

Link to comment
Share on other sites

so where does the green come from on the rotor

Sent from my iPhone using Tapatalk

 

Not sure, some sort of tropical fungus that oozes out of the Filipino rain forest I think, get a lot like that seems to cleanup Ok most times, I hope! 

Link to comment
Share on other sites

i can tell the watches that the indians sell. they have a....how can i put this?......special way with refurbishing the dials. in many cases, if they were just left alone, the watch would be much more desireable.

 

I have my doubts about that Tim, they throw nothing away and the dials they refurbish we would just scrap they would be that bad.

It is not all bad that you can pick their dials, we have several sellers on eBay out here who seem to specialize in re-marketing them, all seem to list them for auction, starting at $85.00 or BIN at $118.00, you or I go on their sites we pick them up no trouble, but check out their feedback and they seem to move plenty of them to happy customers.

 

I put a decent Seiko on ebay at auction and get about $35/40 go figure!

 

Max

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • These types of hairsprings become weak with age and very fragile. Which I expect it is that giving you trouble, and that wheel is not the correct one, if it were not bent I don't think the movement would run as the teeth are not the correct height. The problem you have is price which depends on you. It can be repaired but is it worth it to you, because there is little value in the clock. A wheel can be made and hairspring replaced. Or hang on to it and keep looking on ebay which is your best bet for replacement parts or even a complete movement but it will be like finding a needle in a haystack. 
    • I did that also for a few movements - well, mainly in/around the train jewels. I made big efforts to epilame the mainplate WITHOUT getting Epilame into the Pallet fork jewels (where it's not supposed to be, right?). I made litte barriers with Rodico around that jewel and used drops from a syringe to apply on the rest.  However, I've now stopped doing this. For three reasons: 1. It's a hassle and consumes more of this liquid gold. 2. I didn't see the need when using HP1000/HP1300 lubricants and grease for most part. The two places where I'd use 9010 (i.e. escape wheel and balance) receive Epilame in specific places... or the cap-jewel-setting of the balance suspends the oil sufficiently be capillary action (see my "conflict" about using Epilame on the balance jewels).  3. Lastly, and here I really wonder about yours and others' experiences: I felt that applying Epliame to the train jewels left them looking hazy (borderline dirty) compared to the (painstakingly achieved) sparkly clean results of my cleaning process. I just can't help but think that the Epilame residuals would mix with the oil and cause more friction/wear. I don't know.    simple: it'll stay there. It won't move any further. That's exactly what is happening if you epilame a cap stone. You end up placing the 9010 right on top of the epilame and the oil will sit nicely on that spot.
    • There are some parts on Ebay for the seiko 6020A, it may just be a waiting game for someone to strip one down, NOS will be more scarce . K would strip your movement down to the module then start looking at other seiko movement to see if that coil is used, then seek out a seiko part dealer. Also Retrowatches youtube owner Mike may give you some advice try him on his site . He also hangs around amateur watchmaking groups.
    • I would agree, in order to work harden something you need to exceed it's yield strength when it moves from the elastic zone to the plastic zone and you get permanent deformation and work hardening which is fairly close to its failure point, relatively speaking and dependent on the material/alloy of course. In theory you can load something constantly within its elastic range and not suffer work hardening issues.
    • Probably easier to get a complete new movement - but CousinsUK list it as discontinued. Maybe someone on here knows a substitute movement ?
×
×
  • Create New...