Jump to content

Faulty Seiko NH35a, any guess?

beastiole

By beastiole
in Watch Repairs Help & Advice

 Share

Recommended Posts

beastiole New Member

beastiole

Posted
Posted

Hi everyone,

I am digging into mechanical watches internals because of a faulty Chinese submariner clone that I want to repair.

I have disassembled the whole watch and I think the problem is in the pallet fork. Entry pallet seems too short although it seems OK from the pictures:

20201025_153316.thumb.jpg.e523dbad54ec44dbd470e9e179052775.jpg

And here is the video of the behavior:

 

What guys do think about it? Should I replace the pallet fork or am I missing something else during reassembly?

 

 

 

 

20201025_153445.jpg

20201025_153544.jpg

20201025_153843.jpg

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted

Can you post some more pictures of this movement. Finishing seems downright horrible, escape wheel is stained, the visible portion of the hairspring is distorted. In fairness now is too late to return it, if your goal is simply to complete the watch I would get another mov.t from a reputable seller and not spend more good money after bad.

  • Thanks 1
Link to comment
Share on other sites
beastiole New Member

beastiole

Posted
  • Author
Posted

Sure here some more; although I have reassemble the watch this afternoon. I don't have much.

Since I am learning, this is more of a study movement and I made some scratches in some places.

I can order a new nh35 for 25€, or order a palette fork + club wheel for 8 € (from ebay). So I am hesitating.

From your experience, what could cause this issue?

20201025_153512.jpg

20201025_154201.jpg

20201025_153544.jpg

Link to comment
Share on other sites
DrG Watch Enthusiast

DrG

Posted
Posted

Hi! 

From your video, it appears as if the escape wheel tooth is not locking into the entry stone. The exit stone appears to lock appropriately. Several things to consider. 

  1. Broken or chipped entry pallet stone. 
  2. Loose entry pallet stone. 
  3. Malpositioned entry pallet stone (not making contact with the escape wheel teeth in the locking phase). 
  4. Entry lever/arm of the pallet fork is bent. 
  5. Too much endshake in the escape wheel (on the video it appears as if the escape wheel has a significant upwards vertical shift when spinning). 

I do have some other questions...

  • The movement seems significantly tarnished. Is this an original NH35, or a clone? 
  • Did this happen all of a sudden, or was the watch functioning properly beforehand? Did it happen before or after disassembly? 

In regards to your question about buying a new movement. I would recommend you do, especially considering that the NH35 is a relatively inexpensive movement. 

Best of luck! 

Guido

  • Like 2
  • Thanks 2
Link to comment
Share on other sites
beastiole New Member

beastiole

Posted
  • Author
Posted
4 hours ago, DrG said:

do have some other questions...

  • The movement seems significantly tarnished. Is this an original NH35, or a clone? 
  • Did this happen all of a sudden, or was the watch functioning properly beforehand? Did it happen before or after disassembly? 

Thank you all for your replies.

The movement comes from a Pagani Design submariner homage : PD-1661. I hope it is a genuine NH35a but really not sure about that. Here are some more pictures of the watch.

The watch stopped working (movement was stuck) after 1 day of wearing it. So I decided to dig into it instead of returning it with a 5% chance of being reimbursed...

During the disassembly, I was searching for the issue when suddenly all the power reserved get out of the mainspring with a high speed gear noise when checking the escape wheel. (the balanced wheel was removed, but not the pallet fork). I thought that I had found the issue so I decided to reassemble it and here I am.

I need to check but maybe, it is the bottom jewel of the escape wheel that moved and is making it too low for the entry pallet to block its movement. I will maybe disassemble the dial of the watch and the train wheels to inspect it again.

Thanks again for your tips

20201026_125314.jpg

20201026_125343.jpg

20201026_125400.jpg

Link to comment
Share on other sites
DrG Watch Enthusiast

DrG

Posted
Posted
1 hour ago, beastiole said:

During the disassembly, I was searching for the issue when suddenly all the power reserved get out of the mainspring with a high speed gear noise when checking the escape wheel. (the balanced wheel was removed, but not the pallet fork).

Was the pallet secured in place with the pallet bridge when the mainspring unwound suddenly or was the bridge removed or loose?  Since all the mainspring power was suddenly let down, you have to check for broken pivots in the escape wheel as well as in the pallet. 

1 hour ago, beastiole said:

I need to check but maybe, it is the bottom jewel of the escape wheel that moved and is making it too low for the entry pallet to block its movement.

If this is the case you will need a jeweling tool in order to get the lower escape wheel jewel back in place.

If the entry pallet jewel is out of place, it can be moved, but you will need to measure the appropriate distance from the escape wheel tooth in both the locking phase and impulse phase. This can be done "by eye" or with a dedicated measuring tool. You will also need to learn how to work Shellac in order to adjust that jewel. ?

Your enthusiasm for solving this problem is wonderful!! Even if you buy a new movement (which is my recommendation), keep working on this one until you find the problem. It's the best way to learn in watch repair and watch making. 

Regards, 

Guido

Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
Posted

Could you zoom in and get a higher magnification photo of the pallet fork?

In your second photo of the pallet fork, it appears that the pallet fork has a stress fracture where the arbor goes through the fork arms. Or is it a giant scratch from poor finishing. 

Link to comment
Share on other sites
Watchtime Super WRT Addict

Watchtime

Posted
Posted
10 hours ago, HectorLooi said:

Could you zoom in and get a higher magnification photo of the pallet fork?

In your second photo of the pallet fork, it appears that the pallet fork has a stress fracture where the arbor goes through the fork arms. Or is it a giant scratch from poor finishing. 

looks like reflection to me...

Link to comment
Share on other sites
  • 3 weeks later...
beastiole New Member

beastiole

Posted
  • Author
Posted (edited)

Hi there,

(pictures are not really good and deformed as they are taken using a smartphone with a 8x numerical zoom)

After some investigations, I found what was the cause of the pallet fork not stopping the escapement wheel.

I initially ordered a pallet fork + escapement wheel (sold together) in the objective of replacing the pallet fork .

I compared them but they looked similar: (forged the visible fiber in the newer on the left)

20201103_215751.thumb.jpg.748f4097ae7ecf4bf82c8801c322a350.jpg

I them inspected the movement and tried understand where the problem should lie, and decided to record a video with my phone to see something as I didn't own a magnifier / microscope.

So I removed the escapement wheel and compared it with the new one that come with the pallet fork:

20201103_202645.thumb.jpg.e466f0c93bd84b7fba333b7b81696b4d.jpg

And, voilà. New one on  the left, old one on the right. You can easily spot the difference and understand why the wheel was jumping during the rotation...

I cleaned the fibers that you can see on the picture again, and installed the new one in the watch.

The movement was working again \o/ .... with not much amplitude so the watch was gaining 20sec/min.

I decided to rework the hairspring, after ordering a magnifier, and .... I damaged it ... with my tweezers ...

Fortunately, I managed to fix it and reassemble it. And now ... it works without problems \o/.

The movement still loose a min/day, but I will now try to regulate it.

Thank you.

 

 

 

 

 

Edited by beastiole
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      Yes, I was referring to the (jewelled) gear train with HP (most of the time, I use 1300, but when Rolex says 1000, I'll use 1000).
    • JohnR725
      Without Our Forum

      By JohnR725 · Posted

      did I miss the update of the message of something changing?      
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      I suppose it would depend upon what your lubricating with those? for instance what does the manufacturer say about those lubricants? I have a PDF from the manufacture and a rather peculiar statement found on the bottom of the chart. my suspicion is the reason the recommending would be without epilam the HP oils like the spread except when they're in Ruby jewel's with steel pivots. tableEN lubrication 2020.pdf
    • oldhippy
      Is this a 'hack' ?

      By oldhippy · Posted

      These types of hairsprings become weak with age and very fragile. Which I expect it is that giving you trouble, and that wheel is not the correct one, if it were not bent I don't think the movement would run as the teeth are not the correct height. The problem you have is price which depends on you. It can be repaired but is it worth it to you, because there is little value in the clock. A wheel can be made and hairspring replaced. Or hang on to it and keep looking on ebay which is your best bet for replacement parts or even a complete movement but it will be like finding a needle in a haystack. 
    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      I did that also for a few movements - well, mainly in/around the train jewels. I made big efforts to epilame the mainplate WITHOUT getting Epilame into the Pallet fork jewels (where it's not supposed to be, right?). I made litte barriers with Rodico around that jewel and used drops from a syringe to apply on the rest.  However, I've now stopped doing this. For three reasons: 1. It's a hassle and consumes more of this liquid gold. 2. I didn't see the need when using HP1000/HP1300 lubricants and grease for most part. The two places where I'd use 9010 (i.e. escape wheel and balance) receive Epilame in specific places... or the cap-jewel-setting of the balance suspends the oil sufficiently be capillary action (see my "conflict" about using Epilame on the balance jewels).  3. Lastly, and here I really wonder about yours and others' experiences: I felt that applying Epliame to the train jewels left them looking hazy (borderline dirty) compared to the (painstakingly achieved) sparkly clean results of my cleaning process. I just can't help but think that the Epilame residuals would mix with the oil and cause more friction/wear. I don't know.    simple: it'll stay there. It won't move any further. That's exactly what is happening if you epilame a cap stone. You end up placing the 9010 right on top of the epilame and the oil will sit nicely on that spot.
×
×
  • Create New...