Jump to content

Recommended Posts

Hi everyone,

 

Just starting my journey into repairing mechanical watches because of a faulty NH35a (Seiko SII) in a chinese homage watch.

Owning a bunch of these and a Seiko starlight presage (my Fiancee present).

I hope to find some good advices here.

See ya

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • Is this a good representation of what needs to be done in the disassembly?  
    • Hi all, I'm contemplating the purchase of a "Horotec Watch Tool Hand Press" after damaging a few too many watch hands. I'd appreciate any advice the group might be willing to share. \\\ I connection with my fordite watch dial project, I've been swapping around a lot of watch hands. This practice has been really good for me, and I'm now a lot better about working with watch hands than I have ever been. I'm currently using Rodico, the Bergeon 7404 Set of 3 Watch Hand Install Setting Tools, and a pair of Horotec Aluminum Tweezer with Delrin Tips. I'd say that I can successfully install hands 90% of the time without any damage to the hands or dial. This isn't a great success rate, but it's a heck of a lot better than I was earlier this year. Unfortunately, I've been consistently struggling with some specific watch hands. I'm having a lot of trouble cleanly installing watch hands from the Seiko SRPD## ("5KX" series). The minute hand in particular has been giving me fits. Unlike other hands I have experience with, these minute hands are very broad and thin near their pipe. As a result, it's trivially easy for me to bend these hands during installation which (at best) leaves a slightly visible crease/mark, or at worst results in the total loss of the hand. I have thought about shaving down one of the Bergeon 7404 hand tools -- the root of the problem seems to be that the diameter of the nylon tips on the Bergeon 7404 tools is wider than the area on the watch hands that I'm trying to apply force to, which leads to damage. This would be a cheap solution. I'm also thinking about buying a $99 Horotec Watch Tool Hand Press Single from Esslinger. Does anyone have any experience with this tool? I know that there are cheaper tools that look similar, but I'd be paying the Horotec premium for their precision of manufacture. I'm also specifically considering this tool because it looks to me like all of the interchangeable delrin tips have different diameters, unlike the one-size-fits-all approach of the Bergeon 7404 hands. If the Horotec hand press isn't any good, can anyone suggest an alternative? Thanks in advance for any advice or feedback the community can share with me.  
    • Hey joe, thanks a lot for the advice and I will most definitely keep you and others in the loop. I really wish I could find a service manual for this watch, but what the heck. Do you know what old hippie meant when he said “Just be careful if you remove the wheel on that long pivot. If everything looks OK you might think about leaving it as it is” 
    • As with all indirectly driven min wheel, you wouldn't know about the jewel that min arbour (center seconds) runs through unless you take the min wheel off and inspect all its components under good magnifiction, then you run the risk of the wheel coming loose a few months after reassembly, even when you peen the hole on the minute wheel you can't be sure it stays put for long, when reassembled.  Oiling both sides of pinion on center second is a must and tricky task as the oil might run down on the pinion, lucky giving it an epilame coat helps a lot.  The piece is not ultra rare, yet one worthy of collection is pricy.  I do have some parts to it, so please keep us posted as to how it goes. Good luck. joe      
    • I use stock hands or aftermarket hands, depending on what I think looks good. I tend to use stock hands (with their awesome lumibrite) more, but sometimes I switch it up. I'd like to say that this is always an intentional choice, but sometimes I fumble the hand installation and break a factory hand. I've gotten way better at installing watch hands, but I'm still not perfect. I am considering purchasing a Horotec Watch Tool Hand Press after a particularly painful and expensive loss of a handset from a watch I really liked. I'll be posting separately on this. No plans for indices, lumed or unlumed, in the future ... other than the blued chapter rings I'm still working on. I need to recover my initial costs before buying the equipment I need to ensure a consistent blue, so the chapter rings are still paused. That'd be cool, but no way in heck I'm capable of that. I'll leave that to the pros. 😉 For whatever reason, I've never owned or desired to own a chronograph.  I spent a few hours photographing the watches I've built to date instead of grinding fordite dials over the weekend. I'd like to write a guide for watch photography for folks ... but I've still got a ton to learn.
×
×
  • Create New...