Jump to content

Tip on how to open a completely locked up watch case back

Max

By Max
in Watch Repairs Help & Advice

 Share

Recommended Posts

Max Member

Max

Posted
Posted

I bought a nice vintage chronograph watch with a 7733. Nothing fancy but the watch was just appealing to me and a good start in jumping into the topic of servicing a chronograph. So far I did only one, which was a Heuer pocket watch.

So I wanted to open the case back with a very trusty old stainless steel opener called Vari-Matic.  It did not open, when I tried to clamp the case into a vice and use force with both hands... the HANDLE of the steel opening tool was breaking away! Watch still closed !

I was desperate and after a while chatting with a friend working on cars he explained me that he was wielding nuts to cracked parts to use a ratchet..hmmm..ok wielding might not be feasible but i was trying it with superglue. I took a 23 sized nut sanded it flat an glued it on the back using superglue and let it sit for a couple of hours over night.

This is how it looks like:

IMG_4299.thumb.jpg.d3f08feaeb8fa9577dea78f0a1fcd175.jpg

Next i clamped everything in my large vise and used the ratchet:

Capture.PNG.5d9577ca4ae49fc400d7a987d745c36b.PNG

Voila it was open:

Capture3.thumb.PNG.1bf9cd66d844b10191820447bf0e0052.PNG

And the best thing was that i did not even need massive heat to remove the superglue but dropped the nut and caseback into acetone for about 3 hours and it was gone. No residue just wiping of the back. See the pic below.....now i can service this watch.

IMG_4316.thumb.jpg.a1e4ad83c0c7e941b6c1cfc1737272f5.jpg

I hope this helps someone if he has no other option beside damaging the watch - give it a try - it worked perfectly.

 

Am I nuts or are there others out there doing this?

 

Capture2.PNG

IMG_4300.jpg

  • Like 3
Link to comment
Share on other sites
Pip WRT Addict

Pip

Posted
Posted

Yes, a useful technique when you can’t get your hands on a big Bertha opener. The trick is to use the biggest nut that will attach to the caseback, I learned that the hard way!


Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
chrisdt WRT Addict

chrisdt

Posted
Posted (edited)

Perhaps next time I change the oil in my car I will Superglue a watch case back to the sump plug

On a serious note 'Mole' grips or locking plier grips (end of jaws down) have never failed me.

Edited by chrisdt
spelling
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

Lucky professional back openers are not extinct, All remains to do then is to ask borrow his muscles       :gym: .

Oiling around the rim and letting set overnight is known to have been effective, in which case even he :cold: can open the back. 

Regards joe

 

Link to comment
Share on other sites
Max Member

Max

Posted
  • Author
Posted
On 10/28/2018 at 9:18 PM, transporter said:

i have one question, where did you get your case holding vice/clamp, ive never seen one like that, I like the way each side is a different size to fit between lugs

Sorry for my late reply. I have this beauty from an old watchmaker. Its a bergeon tool

bergeon case holder 4077 is one size, there are different sizes available. But if you google it you will find it.

Greetings

Max

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      So leave off the seconds. Stand the movement on its edge, its the dial edge that rests on the pad ( either rubber or cork , something that wont slip ). Use a finger of your left hand to hold the movement upright,  right hand presses the release and flicks out the stem. I do it this way so i can see what I'm under a microscope. But you could hold the movement between two fingers of your left hand, its the right that has to manipulate the stem out by pushing the release and flicking out the stem with  right ring finger nail. Sounds more complicated than it actually is. I guess you could fix a push pin to something solid, then all you need to do is push the release against the pin, leaving your right hand completely free to pull the stem out.
    • HectorLooi
      Battery

      By HectorLooi · Posted

      Try putting everything back together and closing the back cover. I think one of the two springs has to contact the metal casing to ground the casing. So when you press the button, it will touch the contact on circuit board and close the circuit.
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes, the seconds hand is the longest and goes almost to the edge of the dial. I can’t quite picture it how you do it on the rubber pad
    • Murks
      Battery

      By Murks · Posted

      A don't think so it leaked or damaged it because the watch itself works it just the buttons ain't working not connecting with the circuit board have taken more pictures of where the buttons makes contact with the circuit board.
    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      I think what peter means oh is once he has fitted the hands and  checked for  alignment if them and that they dont foul, how does he then hold the movement to remove the stem in order to case up. The dial cannot be laid on a cushion or in a movement holder as the hands will get damaged. This can be quite tricky for a beginner, what i do is  to stand the movement on edge on a rubber pad so it doesn't slip. Hold the top edge with one finger then my dominant hand uses 3 fingers to press the stem release and flick out the stem. See below peter, leave off the second hand as this is the longest and gets caught the most, then fit it once the stem is out. Alternatively place the movement in one of the cup style holders, i imagine this is what they are designed for. They only touch the very edge of the dial.  
×
×
  • Create New...