Jump to content

Need Technical Manual For Swiss Chrono

jdrichard

By jdrichard
in Watch Repairs Help & Advice

 Share

Recommended Posts

jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted

The counterweight winding mech has fallen out among other things. The guy who gave it to me is a vet chopper pilot and a good guy and really wants to see this thing run again. I a up to the challenge.

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

The only other thing I can find is here. It shows pictures of how the isolating weights are fixed on their watches,if you click on cal families you will see what I mean.

http://www.watchalyzer.com/education/movements/iwc-movements-passion-for-innovation/

Looking on the net there's not much technical stuff about. You could try contacting them.

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

That is an Asian copy of the ETA 7750 and very likely a replica IWC. You should still be able to follow the ETA 7750 guide to service it though.

You have just confirmed my thoughts on the matter. A giveaway, apart from the general finish or lack of, is the blued screws, properly blued screws would be blue in the slots, these are not. They have certainly not been heat blued!

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Purely for aesthetics. You will find this in most high end watches, also the bridges are nicely chamfered and finished. It's worth remembering that Omega and Rolex are not high end watches, I'm talking about the really expensive stuff.

Link to comment
Share on other sites
omgiv WRT Addict

omgiv

Posted
Posted

The blued screws are usually done for decorations purposes. I have blued screws myself over a flame where the slot has not changed. I think it is because the screw was coated in something not removed during the polishing process. I did not polish the screw slot. I think that these screws are possibly blues with a chemical process.

Also, the IWC 79350 is much more finely decorated and finished. It also has a triovis adjustment on the balance.

Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted

Purely for aesthetics. You will find this in most high end watches, also the bridges are nicely chamfered and finished. It's worth remembering that Omega and Rolex are not high end watches, I'm talking about the really expensive stuff.

So Geo, you are pretty sure that this movement is an Asian Replica? If so, I need to tell this guy and slightly deflate his ballon. As well, I will be a bit more aggressive in the repair.

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Mercurial
      AS2063 - hand setting

      By Mercurial · Posted

      Have you got the pallet fork installed in the movement when you see the train move when using the setting works? As nevenbekriev said, without the pallet fork to lock the train, the behaviour you are describing is normal. If this is happening with the pallet fork installed, you have a problem in the gear train, it should be immobile when the pallet fork is locking the escape wheel.  The fit of the circlip above the pinions on that wheel is crooked in your pictures, it should sit flat up against the upper pinion as in Marc’s picture.  Hope that helps, Mark
    • Khan
      Stem broken - can it be rescued?

      By Khan · Posted

      Hi I got a Jaeger LeCoultre K911 movement, where one of the stems was broken. Part no. Should be 401.  Im based in Europe and tried Cousins but its discontinued. They except to get stem in stock for cal. K916 but will that work? Or Is there a way out to join the ends?
    • Bonefixer
      AS2063 - hand setting

      By Bonefixer · Posted

      The part was how it fell out of the movement - the train wheel bridge wasn’t screwed in.    I’ll probably dismantle the part, if I can, to work it out.    The train of wheels ran fine - it was only once the keyless works were installed I noticed the problem. 
    • mthomas828
      Balance staff sourcing?

      By mthomas828 · Posted

      Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
×
×
  • Create New...