Jump to content

Need Technical Manual For Swiss Chrono


Recommended Posts

The counterweight winding mech has fallen out among other things. The guy who gave it to me is a vet chopper pilot and a good guy and really wants to see this thing run again. I a up to the challenge.

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

The only other thing I can find is here. It shows pictures of how the isolating weights are fixed on their watches,if you click on cal families you will see what I mean.

http://www.watchalyzer.com/education/movements/iwc-movements-passion-for-innovation/

Looking on the net there's not much technical stuff about. You could try contacting them.

Link to comment
Share on other sites

That is an Asian copy of the ETA 7750 and very likely a replica IWC. You should still be able to follow the ETA 7750 guide to service it though.

You have just confirmed my thoughts on the matter. A giveaway, apart from the general finish or lack of, is the blued screws, properly blued screws would be blue in the slots, these are not. They have certainly not been heat blued!

Link to comment
Share on other sites

Purely for aesthetics. You will find this in most high end watches, also the bridges are nicely chamfered and finished. It's worth remembering that Omega and Rolex are not high end watches, I'm talking about the really expensive stuff.

Link to comment
Share on other sites

The blued screws are usually done for decorations purposes. I have blued screws myself over a flame where the slot has not changed. I think it is because the screw was coated in something not removed during the polishing process. I did not polish the screw slot. I think that these screws are possibly blues with a chemical process.

Also, the IWC 79350 is much more finely decorated and finished. It also has a triovis adjustment on the balance.

Link to comment
Share on other sites

Purely for aesthetics. You will find this in most high end watches, also the bridges are nicely chamfered and finished. It's worth remembering that Omega and Rolex are not high end watches, I'm talking about the really expensive stuff.

So Geo, you are pretty sure that this movement is an Asian Replica? If so, I need to tell this guy and slightly deflate his ballon. As well, I will be a bit more aggressive in the repair.

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Not exactly John , just have a read through and give us your thoughts.
    • Yep, i pulled that up as well when i was looking,  there is definitely parts out there if you are prepared to go out and find them.  I watched that video years ago, I'm not so sure about probing the coil like that. If you are going to touch the coil use the side of the probe or at least shape a nice round end to it.
    • Hi and welcome to the forum.   As you are already familiar with watches the attachment you may find useful Witschi Training Course.pdf
    • I saw this listing from Australia this morning on Ebay, it might be your only option, good luck.... https://www.ebay.com/itm/145735044565?itmmeta=01HWCRFPEYDDTCXYCRX7ESQH3K&hash=item21ee7c4dd5:g:f2oAAOSwaMhmI5tq&itmprp=enc%3AAQAJAAAA4PzZAWzJj0HOwVM7Xl6qUqGIYly3BvZhzNybkxWf8GJYkKwVh0SpeZ0XYBmoZyjaboPOlJYzdY9svwhQXfR7V%2BiMApTEYFLvJcs8FxTzy1VFCBLR8ADc7V89%2B%2FYvQKdks2KDNNEqAFZN0Hni9zQG078wKL34x0eRK%2Fu843fYdH%2FVIAiOZ5%2BbOmySNdu%2Bv4cSemywC%2FWfaiI%2Fj5D3YWk2PaySdPfu7lUaMadcyhmHZM6l6NllJd1eK%2BdblkJD98pTzVuxRDne5AQaCYawls%2FaoQK9B7epV%2B87TIbD9Ulr4qdC|tkp%3ABk9SR-rnvpjjYw
    • Hi. In the picture not only does it depict that the wheel is bent but also the plate or is that due to th angle of the picture.  Already received very good advise so I will butt out.
×
×
  • Create New...