Jump to content

spade drill bit set


luiazazrambo

Recommended Posts

Don't know about the origins, but that's old school stuff there (at least whoever was using it was old school). Those arbors would hold the drill, the pointy side would fit in a divot on the side of a bench vice, and the plate or whatever held against the drill while the arbor was driven by a bow. Lot of crazy work was done with that crazy setup.

  • Like 1
Link to comment
Share on other sites

Hi  Back in time the British Army R.E.M.E. repaired a lot of army instruments them selves, nothing being out sourced. They had their own Watch repair department which was fully equiped with all the tools. I was once priviledged to enter one of these workshops on a work visit and chat to the men, they repaired all small instruments including compasses. The arrow mark is indeed M.O.D.

  • Like 1
Link to comment
Share on other sites

Yes, i bought this set because I liked it. Since i found that WWW eterna ( dirty dozen ) in the dirt i always notice the broad arrow if its somewhere around me. I bought it off ebay and I would love to learn more about it, or the people who were repairing watches for MoD and using these tools.

Link to comment
Share on other sites

11 hours ago, watchweasol said:

Hi  Back in time the British Army R.E.M.E. repaired a lot of army instruments them selves, nothing being out sourced. They had their own Watch repair department which was fully equiped with all the tools. I was once priviledged to enter one of these workshops on a work visit and chat to the men, they repaired all small instruments including compasses. The arrow mark is indeed M.O.D.

Where was this workshop and when did you visit them? Is it possible to do such a visit still?

  • Confused 1
Link to comment
Share on other sites

Hi    The workshop in question was at York R.E.M.E strensall where I visited to repair computer equiptment in their workshop so got to know some of the men. most were apprentice trained by the Army then.  The workshops were all closed down about 20 years ago when the Britsh Army were leaving Germany.  I visited them as well before the shut down Moenchengladbach was a small military vehicle workshop,  Willich was a REME engineering workshop and Wetter on the rhur was a heavy tank refurbishment work shop sadly all closed. there still are centralised workshops in the UK but only civilian contractors are allowed in on legitimate business. There are no casual visitors allowed at all.  They are guarded by the MOD Police on the gatehouse .

  • Like 1
Link to comment
Share on other sites

1 hour ago, AndyHull said:

I wonder how those drill bits managed to be "liberated" from the MOD in the first place.

I have an identical set. They came to me in a job lot from the estate sale of an old watchmaker who apparently was trained by the army prior to his being demobbed after the war so that he had a trade to go into. 

  • Like 1
Link to comment
Share on other sites

1 hour ago, luiazazrambo said:

I like both the practicing and the tower. I heard they used to mint silver and gold coins there. :)

They also used to perform complete cranial amputation. On the plus side, they do store a lot of very expensive baubles there too, so if you can tunnel your way from your cell to the strong room, you might be able to make off with a bling-tastik hat or two. :P

Link to comment
Share on other sites

Hi  The tower as well as cranial amputations had an intersting side line in bodily investigations, Thumb screws, hot irons (not for pressing clothes), removal of fingernails  A Tudor manicure No anesthetic not to mention dentistry. A good supply of rats was available for company. So entering MOD property uninvited has its problems.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • No idea Rich, but for your own sake please avoid inhaling the fumes.
    • I would try the vapour treatment very simple just a simmering pot of the stuff and jewels bluetacked ( not whitetacked this time, you still haven't said if I'm forgiven yet 🙂 ) to the underside of the lid. You're now gonna tell me that stearic acid can be highly explosive above 90° C 🤣
    • I guess it also depends on the precision and quality of the watch. He works on vintage watches mainly and surface treatments on 50 - 60 year old watches probably isn't going to make much difference. I read about nano coatings for car finishes. The article claims that nano coatings can reduced the coefficient of drag by 5%. Is that number significant? I don't know. Maybe if you were trying to break the land speed record. But applying that on a 50 year old clunker isn't going to make it go any faster, accelerate better or save on petrol. 🤣
    • 😅 yep certainly overdid it , i wasn't sure if i had enough heat so i went out and left it cooking. You can see the thick frosting, bit like my cherry buns.
    • 5 hours! You have slow cooked it! It must be really tender by now. @nickelsilver posted about his Greiner machine a while back. It had a heated chamber of stearic acid to epilame jewels and it only took 60 seconds. I've tried stearic acid dissolved in ethanol with a flake of shellac. I'm not really convinced by my test results. I conducted a side by side test by coating a mirror with a stripe of stearic acid and putting several drops of 9010 on the treated surface and untreated surface and observed it for several days. The 9010 spread out about the same for both the treated and untreated surfaces. I spoke with my mentor recently regarding epilame and lubricating pallet jewels. He has stopped doing both because he finds no significant improvements to the end result.
×
×
  • Create New...