Jump to content

Omega Speedmaster Moon Watch Question


Recommended Posts

I suggest a full service every 5 years wether there is evidence of a problem or not. 

 

Oil degrades and becomes less useful over time and it needs to be cleaned and renewed to reduce wear, just like with any mechanical item (a car being the most obvious)

 

:)

Link to comment
Share on other sites

It's a bit like a car. You can run it and run it and not worry and the, one day - bam! the cam belt's gone and you're into a major spend. I think a basic clean and service after 10 years service wouldn't hurt, and will get rid of that oil drying round the jewels...

 

Hah - just cross-posted with you, Mark!

Edited by WillFly
  • Like 1
Link to comment
Share on other sites

Hi rattandson,

 

I would service it in order to avoid a failure! Being an Omega, you can either send it to the factory or do it yourself/professional. The whole point is doing it properly and avoid, as previously said, a failure that might endanger other parts of the watch and make the service more involved (costly, time consuming, etc). I think service as preventive!

Link to comment
Share on other sites

Rattandson your question seems to have a least two components. I'll handle both: 1) Does a gorgeous high-quality watch like an Omega moon watch deserve to be serviced after 10 years of working without fail? Yes it does ! 2) Would I do the service myself? Probably not because I have a fear that I will totaly mess up any of my Omegas--especially if they have complications. The moon watch is a chronograph....major complication.

 

JC

Edited by noirrac1j
Link to comment
Share on other sites

I recently got the very same watch and I will definitely be getting it serviced every 5 years to keep it in tip top condition. I'd wanted it for a very long time and never intend to sell it so want to look after it. That gives me 5 years to get good enough to service it myself or more likely give it to Mark!

Link to comment
Share on other sites

It's a bit like a car. You can run it and run it and not worry and the, one day - bam! the cam belt's gone and you're into a major spend. I think a basic clean and service after 10 years service wouldn't hurt, and will get rid of that oil drying round the jewels...

 

Hah - just cross-posted with you, Mark!

 

 

ahh the old car explanation when talking about servicing..... the most used and best example....

Link to comment
Share on other sites

ahh the old car explanation when talking about servicing..... the most used and best example....

Yup - an old chestnut - but worth repeating.

 

I'm always amazed at the people who think a watch should be serviced for next-to-nothing - and then cheerfully shell out £200 every year for their car to be serviced. When you think of the potential wear and tear on a fully functional mechanical movement over, say five years...

Link to comment
Share on other sites

It's the only thing people are most likely to service on a regular basis, so it's a natural illustration.

 

But we can talk about boilers if you want :) I had a new combi boiler fitted in my house five years ago - at the time all the rads and pipes were flushed and chemicals were added to clean the crap away.

 

I have not had it touched since and now just last month the hot water kept cutting out (painful mid-shower). If I had it serviced every year in accordance with the manufacturer guidelines would have escaped a lot of grief, agro from the wife and cold showers.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I'll have a look for it, but don't hold your breathe. Failing that I'll make another video when another bezel needs to be removed.
    • The UK lots can be a 404 hit or miss, 6 - 10 watches can come in anywhere from 20 - 50 quid. I once had a 404 division of 8 watches for a fraction over 30 quid, one of them was a Smiths Astral model National 17 an absolute certainty for winner contender. The crystal was scrached up to the point of being very difficult to see the brand, something triggered a gut feeling in me and it paid off.
    • I just picked up this Mondaine quartz watch on tradera.com for £11. It's a non-runner so I will replace the Ronda movement (£10.95 at Cousins), polish the case, replace the case-back gasket, and replace the mineral crystal. Now, the problem is finding a suitable crystal. The original crystal is slightly domed (2.4mm thick dome), measures 36.4mm in diameter, and is 1.3mm thick at the edge. The closest I can get on CousinsUK is 36.5mm in diameter, 3.1mm thick dome, and 1.5mm thick at the edge. I think the replacement crystal would look OK, but the problem is finding a suitable glass gasket. The case diameter for the glass gasket is 36.9mm and the closest glass gasket I can find on CousinsUK is either 36.8x36.0mm or 37.0x36.2mm. I guess one of those glass gaskets could work but as you can see there's no way the 36.5mm domed crystal would fit the inner diameters of those glass gaskets. I guess I will have to give up on a domed crystal, no? So, the backup plan is to use a (1.5mm) thick flat mineral crystal as the diameters come in increments of 0.1mm. But, what glass gasket would be the better option? The one with an outer diameter of 36.8 (0.1mm too small) or the one with an outer diameter of 37.0mm (0.1mm too large). Again the case diameter for the glass gasket is 36.9mm. I believe I read or heard that the crystal diameter should be 0.1mm wider than the inner diameter of the glass gasket. Is that correct? I'm sorry for all the numbers. I've tried to make it as clear as I could. So, I'd appreciate your thoughts on this. BTW, measuring and sourcing crystals and gaskets is extremely time-consuming! 😓
    • Lots to choose from... Just sayin'.
    • Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement. 
×
×
  • Create New...