Jump to content

Stuck Screw Back


Recommended Posts

Hi everyone,

I know there has been previous topics on this but I have a Armani watch a customer brought to me to replace the battery and a stem. I have tried everything and nothing will budge it now my question is on super gluing a bolt on the back of the watch. I know you soak it in acetone after the back is off to remove the bolt and get rid of the glue. My worry is that once I glue this bolt on that it still wont move and if that is the case then how would i remove both the bolt and the super glue because i cant soak the whole watch in acetone for the obvious reason. Im also open to other suggestions as i have used every tool and trick i can think of.

 

Thanks

Link to comment
Share on other sites

What does the caseback look like? If its the standard 'water-resistant'  threaded type,  and you've tried a Jaxa wrench with no success, gluing a bolt onto the back does indeed work. I usually do it with JB weld epoxy which forms a very strong bond and it has always worked. Getting the bolt off requires heating it up with a pencil tip butane torch (!)

Using superglue should work, but if it doesn't you can always take a glass eye dropper and place a few drops of acetone around the bolt to get it off. My concern would be if the superglue DOESN't work and the bolt just pops off of the caseback when you apply wrench torque.

J  

Link to comment
Share on other sites

Thanks, yes it is your typical water resistant threaded case back that has not had a battery changed on it. Guy bought it about six months ago so it is tight from the factory. Never thought of using an eye dropper, thanks for the info im going to try the super glue trick first and go from there

Link to comment
Share on other sites

Do you know a friendly watchmaker with a Big Bertha? That’d be the way to go if at all possible. They really are stupendously good.


Sent from my iPhone using Tapatalk

  • Like 1
Link to comment
Share on other sites

Normally glue a nut on rather than a bolt.

Once off I just put some super glue remover in the centre of the nut which acts as a well and leave it a while to slowly seep out over some hours.

Guess you'd be able to do that even if the back didn't come off.



Sent from my Moto G (4) using Tapatalk

Link to comment
Share on other sites

1 minute ago, nad said:

Normally glue a nut on rather than a bolt.

Once off I just put some super glue remover in the centre of the nut which acts as a well and leave it a while to slowly seep out over some hours.

Guess you'd be able to do that even if the back didn't come off.



Sent from my Moto G (4) using Tapatalk
 

Yes indeed. I've used bolts, but a nut is easier to work with although I've only used Epoxy which definitely works. The caseback might get a little residue stain on it, but you can sand that off with superfine grit paper.

J

Link to comment
Share on other sites

No stains when using superglue and no need to use abrasive paper. The remover softens the glue so easy to get off with your nails.

Also find it easier to leave the super glue set over night and use a small socket driver rather than spanner. This allows you to exert a little downward pressure when un screwing the nut which normally helps in my experience.

Sent from my Moto G (4) using Tapatalk

Link to comment
Share on other sites

5 hours ago, fuse63 said:

Hi everyone,

I know there has been previous topics on this but I have a Armani watch a customer brought to me to replace the battery and a stem. I have tried everything and nothing will budge it now my question is on super gluing a bolt on the back of the watch.

Everything like what? Picture of the watch and which tools have you used?

Link to comment
Share on other sites

  • jdm locked this topic
  • Mark unlocked this topic

All off-topic posts removed - this is how it will be from now on. Please please please keep threads on topic out of respect for the OP. Please please please - no bickering, and that goes for everyone.

It makes our forum look bad - we are a group of great people, we can keep it that way.

If anyone spots this happening again from now on - please report the post - there is a link above every single post, I will be on it like flies on a turd. :D

now - back on topic, pretty please ;)

  • Like 3
Link to comment
Share on other sites

6 hours ago, Mark said:

All off-topic posts removed - this is how it will be from now on. Please please please keep threads on topic out of respect for the OP. Please please please - no bickering, and that goes for everyone.

It makes our forum look bad - we are a group of great people, we can keep it that way.

If anyone spots this happening again from now on - please report the post - there is a link above every single post, I will be on it like flies on a turd. :D

now - back on topic, pretty please ;)

GOOD DAY MARK. THANKS!

 

REGARDS,

J

Link to comment
Share on other sites

I have a titanium case with a titanium back (dumb) that is probably galled together. Respectable brands use a stainless cover on a ti watch so they don't gall.

Anyway, my plan is liquid nitrogen. I will place the cover wrench on, fill the center with liquid nitrogen, wait a fe seconds and try again.

If that doesn't work, I may try JB weld although I'm not sure how it will hold up at super-low temps. Note on this watch I know the male thread is on the cover, so shrinking it back from the case with the nitrogen should work (in theory).

It's in "the pile" to get to at some point...

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Its a touch under ive just remeasured it and added a wrist shot. Unbelievably it was £13  plus 3 postage. You dont find watches that nice for that money every day of the week. Maybe removing the epilame in the oil region improves the purpose of it. We may know very soon as i emailed Episurf 4 hours ago to ask that exact question. 🤞they are happy to provide an answer for us. How do you fancy trying a stearic acid vapour treatment experiment  H .  Shall i have a go this afternoon ?
    • That's the size of my grandfather's Ernest Borel watch. Definitely not a lady's watch! 👍
    • Thanks H It does have a big crown for the watch , it could be considered a ladies watch these days i guess, it measures 33mm case 36mm with that large crown 18mm lug space. A tad small for a guy of today, but still very wearable. The photo was deceptive so here it is adorning my 7 1/4 " wrist. It need some love to make it run better. The hair coils are touching so running a bit fast at the moment,  not caused by magnetism, and maybe just a clean and a service. The dtal is in fantastic shape.
    • That's one beautiful timepiece! Love the big crown in proportion to the case. Perhaps a ladies' watch, but I don't think so. I have a "modern Ingersoll" watch, but it has nothing to do with the original brand (Miyota 9015 movement). Interesting synonym for synthetic oils! 😆 There is, of course, a limit to how large a volume of oil epilame can bind and hold in place. If the oleophobic effect is too strong then it can become a problem. I'm not sure where I heard or read it, but as I understand it, the active ingredient in a bottle of epilame is extremely small and more than 99% of the contents of the bottle is just a transfer agent. If the active ingredient becomes too concentrated, which it can become over time, or if the product is of poor quality, the oleophobic effect is amplified. This in turn causes the applied oil to look like a gummed-up ball on the surface of the treated part. If that happens, we know that the active ingredient has become too concentrated. What we want is for the oil to bind but not to the point where it is formed into an excessively round ball on the surface. The highlighted text in the patent that you refer to describes well the problem that can arise with too high a concentration of the active ingredient. However, I would be extremely surprised if the entire amount of oil leaves the treated surface as water on wax would. At present, I am convinced that the analogy between wax and water on the one hand and epilame and oil on the other is incorrect. Epilame is described as binding and that is also my absolute experience. Epilame probably has some repelling effect but that is not its main purpose and that is not how epilame is designed and works. The method of abrading the epilame treatment from the section of the pallet stones coming in contact with the escape wheel teeth seems after even more research to be well established, but if it actually works, if so how and why is beyond what I can currently understand. Perhaps it is just to do and trust that it is based on well-established experience. I am, after all, inclined to think so.
    • Sorry to jump in here, but I didn't want to start a new thread when there's already one regarding the second hand watch market. Can anyone tell me what I should be looking at when buying watches from eBay? I see loads on there for quite cheap, but after reading this thread I'm guessing they're all garbage and not worth the time? I recently bought an old Elco watch for 99p, just to practice on. I'm also really fond of the look of Services watches and Smiths Empire watches. I keep seeing them listed for around 5 or 6 pounds. Are they not worth the time buying? I'm not looking to sell watches to make a profit. I just want to buy watches I like the look of and wear them, but I also don't want to buy things that are going to be impossible to find parts for, or that have already been abused by someone else and broken beyond repair. Any tips?
×
×
  • Create New...