Jump to content

Omega Constellation won't open

Watchtime
 Share

Recommended Posts

Watchtime Super WRT Addict

Watchtime

Posted
Posted

Today I got this Omega Constellation I have never seen before, around late 70's? It has kind of octagonal shape and has a quartz movement with quicksetting. As the back is already damaged by the previous owner, I wonder how to open this one without further damaging it as I would like to know which caliber is inside. Appreciate your help guys.

IMG_1412.jpg

IMG_1416.jpg

IMG_1419.jpg

IMG_1420.jpg

IMG_1422.jpg

Chopin Super WRT Addict

Chopin

Posted
Posted (edited)

It has a snap off case back. That means you have to pry it open. Do you have a case back knife ? You could also use a knife with a thin (but durable) blade that isn't sharp or pointy so that you won't damage the case.

Look for a small slot/space somewhere along the case back as that is where you should insert the knife. Unfortunately not all watches have that...

You can also try to use a rubber ball and rotate it around a bit to free it from potential gunk and afterwards pry it open but that won't always help.

Edited by Chopin
  • Like 1
Watchtime Super WRT Addict

Watchtime

Posted
  • Author
Posted

In addition: The minute hand is set by turning the crown as usual but the hour hand is set by pushing in the middle of the crown. The hand then will run forward.

Watchtime Super WRT Addict

Watchtime

Posted
  • Author
Posted
4 minutes ago, Chopin said:

It has a snap off case back. That means you have to pry it open. Do you have a case back knife ? You could also use a knife with a thin (but durable) blade that isn't sharp or pointy so that you won't damage the case.

Look for a small slot/space somewhere along the case back as that is where you should insert the knife. Unfortunately not all watches have that...

You can also try to use a rubber ball and rotate it around a bit to free it from potential gunk and afterwards pry it open but that won't always help.

thanks Chopin...there is no space whatsoever, I guess that explains all the scratches on the side of the caseback. I will give it a go with the squeezeeball, see if it turns a bit.

  • 2 weeks later...
jdm Distinguished Member

jdm

Posted
Posted (edited)

You can buff off the scratches. Just tape out the brushed part as that is more difficult to repair.

Edited by jdm
  • 2 months later...
VickyC New Member

VickyC

Posted
Posted

Hi, i'm a total newbie here. 

I have exactly the same watch, which my partner bought for me as a birthday present about 4 years ago now. 

However, unfortunately i have never worn it because it isn't complete. He thought it would be quite easy to source a dial and hands for the 1330 and this watch case. To complete it. 

But it has proven harder than we thought. Can you help in any way as to where i can get a dial for this watch, hands etc. i have tried many a dial that is the right size as the case however they are not compatible with the case. 

I would love to be able to wear this watch. I love it so much. 

Any help or advice would be gratefully received..

Many thanks in advance.

 

 

ro63rto Distinguished Member

ro63rto

Posted
Posted
Hi, i'm a total newbie here. 
I have exactly the same watch, which my partner bought for me as a birthday present about 4 years ago now. 
However, unfortunately i have never worn it because it isn't complete. He thought it would be quite easy to source a dial and hands for the 1330 and this watch case. To complete it. 
But it has proven harder than we thought. Can you help in any way as to where i can get a dial for this watch, hands etc. i have tried many a dial that is the right size as the case however they are not compatible with the case. 
I would love to be able to wear this watch. I love it so much. 
Any help or advice would be gratefully received..
Many thanks in advance.
 
 
Welcome and good luck sourcing the parts.

You could send a message to
http://www.ofrei.com/page665.html
And ask availability.
StuartBaker104 Distinguished Member

StuartBaker104

Posted
Posted

Or if you are in the UK then try Cousinsuk.com

You will need to provide the case number which is inside the caseback - probably  395.0802 if the same as the watch above. Alternatively you could try one of these items from eBay which have case, dial and hands:

182937592182

162781970733

 

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • nevenbekriev
      Elgin Grade 315: Runs/stops with dial down/up

      By nevenbekriev · Posted

      Yes, what I wanted to say is that the cock is part of the main plate, manufactured together with it and not meant to be interchangeable. Even if the other cock gets in place, it is not sure that the balance then will stay upright. You should use the original cock when it exists and is not destroyed. The adjustment needed by bending it is not irreversible. It is minimal deforming that is needed. No tools are needed. I have pointed to all needed references here for the balance staff endshake checking and correctness confirmation. The only tool needed for the correction is You thumb. The cock must be fixed on the main plate, no need of special plate with holes and so on. If You will feel more confident, then measure with Vernier caliper the height of the top of the cock where the stones are against the main plate bottom when the shim is fitted and try to reach the same height when bending the cock (with no balance in place!!!) Caliper with screw for fixing is perfect.    
    • LMS
      Thermal Bluing Issue

      By LMS · Posted

      Thanks for the reply. I polished the head of the screw using 1500 to 10000 lapping paper and a screw polisher. This is why I think the head blued and the rest of the screw didn't. Silly question, how do you polish the whole screw inc threads, if that's what it needs to blue? 100% clean, Elna red and heated ultrasonic bath + IPA rinse. Finally, there is definitely heat leak as there's about a 30c difference between the brass bed and the soldering station temp. Having said that, the bed temp was stable. I will try to search out a better brass pot, but I haven't found one yet, hence the stainless steel bowl. 
    • RichardHarris123
      Removing stem from compressor-style case

      By RichardHarris123 · Posted

      Agreed but that's where WD40 excels, water displacement. 
    • tomh207
      Thermal Bluing Issue

      By tomh207 · Posted

      I would change the container to a thick walled brass one to start with. Looking at you screw pictures they don’t look shiny enough, really it’s best to do a black polish on them before trying. Also make sure once polished they are scrupulously clean, I dunk my experiments in acetone before bluing.   i think the thin walled stainless container to leach away the heat from the shavings, most successful bluing videos for example use thick walled brass to hold a good deep amount of shavings which acts as a better holder of heat.   Tom
    • rehajm
      What's your thoughts on this Rolex Sea-Dweller, ref. 16600, calibre 3135 project?

      By rehajm · Posted

      …I guess my friend’s dad was duped…and by a Rolex dealer… …well, it’s a good fake 🤪 even the box and papers look legit…  
×
×
  • Create New...