Jump to content

My Basic Watch Repair Tools

jdrichard

By jdrichard
in Tools & Equipment

 Share

Recommended Posts

jdrichard Distinguished Member

jdrichard

Posted
Posted

My current collection of watch repair tools. All tools have a special purpose and there are only a few duplicates, where I found a more professional tool. You basically need all these tools to repair watches. Did not include and oils or cleaning solutions. Did not include my ultrasonic cleaner or and timing tools (I use both PC and Tab Software). Did not include my Drummel tool used for case polishing .59cecdb313155f4bc4c8e6faf9767512.jpg94c9959b45c27b417334b356bc38614d.jpg

 

 

Sent from my iPhone using Tapatalk Pro

  • Like 4
digginstony Super WRT Addict

digginstony

Posted
Posted

Oh, below the sleeve wrench to the right, looks like you have not one but two ! K&D balance staff removers. There getting very hard and expensive to get hold of these days. Excellent set off tools

Sent from my SM-T585 using Tapatalk

  • Like 1
rogart63 Distinguished Member

rogart63

Posted
Posted (edited)

Nice tool set you got. Have Jacot tool but it's probably worn or something cause the pivots never run in the groove as they should. Or if it's me  that don't now how to use it properly. 

Edited by rogart63
  • Like 1
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
Very nice selection. And is that a K&D sleeve wrench and mainspring winder I can see in the top left hand corner ? [emoji3]

Sent from my SM-T585 using Tapatalk



Yes it is


Sent from my iPhone using Tapatalk Pro
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
Oh, below the sleeve wrench to the right, looks like you have not one but two ! K&D balance staff removers. There getting very hard and expensive to get hold of these days. Excellent set off tools

 

Sent from my SM-T585 using Tapatalk

 

 

One is for watches and the other is for Pocket Watches. And they were hard to get.

 

 

Sent from my iPhone using Tapatalk Pro

jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
Nice tool set you got. Have Jacot tool but it's probably worn or something cause the pivots never run in the groove as they should. Or if it's me  that don't now how to use it properly. 

I mad a video on YouTube on how to use the Jacot tool. No way the grooves should be worn out.


Sent from my iPhone using Tapatalk Pro
chrisdt WRT Addict

chrisdt

Posted
Posted

I think I might give up.. I thought I only needed a bed spanner, lots of enthusiasm and a rubbish bin to put all the watch bits in!!!!

  • Like 2
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
A nice starter kit lol!!!
Very nice set indeed. :thumbsu:

My wife has started to notice all the tools coming in the mail over the years. She usually says "why so many?, You can't use the all at the same time". The is what she says about my guitars....don't ask how many.

Sent from my GT-N5110 using Tapatalk

jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I think I might give up.. I thought I only needed a bed spanner, lots of enthusiasm and a rubbish bin to put all the watch bits in!!!!

I started small years ago and every time I needed to fix something unique, another special tool was required. I still don't have a lathe or a cleaning machine. Next year.

Sent from my GT-N5110 using Tapatalk

dadistic Distinguished Member

dadistic

Posted
Posted

I think jeweling tool is next for me. I already have the Jacot,  don't know why I bought that first, except that a very nice one (with a bow!) came up at a good price. 

  • Like 1
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I think jeweling tool is next for me. I already have the Jacot,  don't know why I bought that first, except that a very nice one (with a bow!) came up at a good price. 

I am still looking for a bow for my jacot, however, the badge reel works very well. The jeweling tool I have used a lot. Most old pocket watches that have a bad jewel have a cracked jewel on the third wheel, lower...don't know why, perhaps the forces there are greater. So I have pressed in a few jewels. I have also pressed in jewels on a 7750 watch and a few others.

Sent from my GT-N5110 using Tapatalk

  • Like 1
evn137BANNED Member

evn137BANNED

Posted
Posted

Reminds me of the adage " He who has the most toys wins ". My wife usually says when another package ( my watch tools ) comes in, " Everyday is Christmas ."
Anyway, happy for you. Keep it coming!


Sent from my iPhone using Tapatalk

  • Like 1
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
Reminds me of the adage " He who has the most toys wins ". My wife usually says when another package ( my watch tools ) comes in, " Everyday is Christmas ."
Anyway, happy for you. Keep it coming!


Sent from my iPhone using Tapatalk

My wife says exactly the same.


Sent from my iPhone using Tapatalk Pro

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • dnhb
      Loose roller table

      By dnhb · Posted

      Thank you very much for this. Re: 1. I've so far found that this one needs something thicker than 2x kitchen foil (another suggestion in that thread)! 2. I've been checking where the roller needs to be in relation to the wheel, the hairspring stud/arm & the pallet fork to try to get it right first time. 3. Does one raise notches at both ends of the tube? 4. What is a "driver roller sharpener"?
    • mbwatch
      Elgin Grade 315: Runs/stops with dial down/up

      By mbwatch · Posted

      Hmm, if it is sitting that low I am not sure I would blame end shake (which would be to blame if you turned it DU and the hairspring touched the balance cock). If it is sitting so low that the balance rubs on the pallet bridge I would verify that the balance arms are not dished downward and also that the lower balance jewel doesn't have an issue such as being chipped. Or the balance staff is actually too short, which would have caused your earlier end shake problems too. If you install the pallet bridge without the pallet fork and install the balance, is your free oscillation still good or is it immediately bound up on the pallet bridge? (I have an elgin watch like that where someone in the past ground down the pallet bridge significantly) Yes, you'll need to rotate the hairspring but deal with the pallet bridge interference first.
    • docrpm
      Elgin Grade 315: Runs/stops with dial down/up

      By docrpm · Posted

      Ok. So given that I had free oscillations DU/DD for roughly the same time, I reassembled with the pallet fork and bridge underneath, and now I can see two more problems.    1. The arms of the balance are nearly flush with the pallet bridge. Bad. I can speculate as to why…the end shake still looks to be too much. Maybe other causes as well? 2. The balance doesn’t spin freely. In the resting position, it looks like the impulse jewel is outside the jaws of the pallet fork. Not by much, but still outside. If it needs be inside in the static position, then I’m guessing I’ll need to rotate my hairspring collet to change orientation by a few degrees.    The journey continues…
    • stm
      Doxa women's watch (radioactive)

      By stm · Posted

      Ok, that's good to know, thank you.
    • Michalzeszen
      ETA 2472 - how to tackle this crown and stem?

      By Michalzeszen · Posted

      Andy, why you betray me?   I may have good news. I'll share later! I have contacted an old watchmaker from my town, and the guy has it all. He is offline, so no parts are available to purchase, but he offered to send one for less than 10 USD, which is great. I'm now checking if he has an oscillating weight as well, to close up all that I need to put this movement to work.   Thank you all for the support. And if any good soul finds a video of the assembly process of this stem and crown, it would complete my day!  
×
×
  • Create New...