Jump to content

$500 Haul of clock tools

LittleWatchShop
 Share

Recommended Posts

nickelsilver Distinguished Member

nickelsilver

Posted
Posted

The collets look to be mostly Levin- that set is worth 3x what you paid easily. The bushing tool and accessories probably 2x. Nice find! The lathe looks to be Peerless (perhaps marked Marshall-Peerless), not the best but it does have the collet holding tailstock with it great.

  • Like 1
Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
44 minutes ago, rehajm said:

Yes a nice haul. Not everyone’s a flipper- I frankly find it to be a PITA. If a knowledgeable fellow makes a few quid sorting out unwanteds and finding them good homes the world is better off. Well done!

I am a hoarder.  Now I have seven lathes. 

  • Haha 2
Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted
6 minutes ago, LittleWatchShop said:

I am a hoarder.  Now I have seven lathes. 

Between you and JD that's like 20 that are off the market and everyone wonders why they keep getting more expensive 😂.

 

I have had one watchmaker lathe for the last 24 or so years- but it has literally about 10k hours of use on it in that time, haha. Well, I recently found another identical one for a song so I had to get it, good to have backups.

  • Like 2
Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
4 minutes ago, nickelsilver said:

Between you and JD that's like 20 that are off the market and everyone wonders why they keep getting more expensive 😂.

 

I have had one watchmaker lathe for the last 24 or so years- but it has literally about 10k hours of use on it in that time, haha. Well, I recently found another identical one for a song so I had to get it, good to have backups.

Three of my lathes are setup for dedicated use. 1) primary turning (Levin), 2) graver sharpener (Peerless), 2) remote office general purpose (Peerless).

I started with the two Peerless that my dad left me.  Kept searching for better precision and then discovered Levin and searched for that.  My Levin with cross slide and 4-jaw chuck, collet tailstock, also came from FB for $300...another good deal.

  • Like 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted (edited)

I have spondylitis of the neck which was caused to poor posture. When I was around 40 xrays showed the wear I had was from someone in their 70's I have to take meds for the rest of my life, some times now my neck locks and I can't move my head very well.

Edited by oldhippy
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Mechatronics Engineering v Mechanical Engineering

      By RichardHarris123 · Posted

      @HectorLooimakes an excellent point, the degree should be brilliant and more than useful but if it's not recognised, then the job options are limited.  You need to find out how many companies are willing to accept Mechrotronics. 
    • watchweasol
      ETA 9362 check electronic module

      By watchweasol · Posted

      Hi other than testing the coil without the proper tools it will be difficult.  If you +an rig up an external supply and attach it to the cut block you may be able to pick up the pulses on the chip if not on the coil. i have attached the parts sheet for the watch 9362 which gives you the part number of the cut board assembly, whether this part is still available or not , who knows. ETA 9360, 9361, 9362.pdf
    • nevenbekriev
      Hamilton Khaki Mechanical / H-50 winding issues

      By nevenbekriev · Posted

      Hi and welcome. First of all, check the power reserve. If the watch is runing, this means the spring is attached to the barrel arbor. If there is no end of winding, this probably means that the spring is not attached to the barreland it's outer end is slipping. In such case, the watch will run, but the power reserve will be small - about several hours
    • watchweasol
      Hamilton Khaki Mechanical / H-50 winding issues

      By watchweasol · Posted

      Hi welcome to the forum. One can only reiterate the diagnosis already made by clockboy mainspring problem. But before tearing it to pieces take a little time to read the attached file to acquaint yourself with all the various parts. TZIllustratedGlossary.pdf
    • Geotex
      B-Dip residue?

      By Geotex · Posted

      We think about these preps as "one-dips" partly because they are terrific solvents but also because the parts they are used on are often cleaner in general than many other parts. But old oils petrify, and even something like B-Dip can't clean up over-soiled parts without some extra effort, as mentioned above. There is an intermediate step during cleaning where the solvent can partially dissolve tarry residues so they have a more liquid varnish-like consistency, and that could well be what you are seeing on the coils after two washes. I wouldn't worry that your B-Dip was contaminated before you used it on this hairspring, but it I wouldn't re-use that aliquot AFTER this cleaning!
×
×
  • Create New...