Jump to content

Some More For Restoration.


Geo

Recommended Posts

Thanks guys, you get a far better deal at a local auction than eBay. The wee stainless Omega dates from 1939 and has a 23.4SC movement. The other is a 1972 Omega Geneva with 1481 movement. The Favre is a single barrel movement, I don't know the calibre yet.

None were working, but on first very quick inspection, the old one had the second touching the minute hand and after a wee week it is running fine. The Geneve balance swings fine but will not run and the the rear gasket is goo. The Favre runs OK, but looks like the cannon pinion is slipping. So hopefully they will all be going well after a good service.

Link to comment
Share on other sites

Good stuff, Geo. Out of interest, was there a buyer's commission on the auction?

There sure was Will, including VAT it worked out at 25% in total. Even with this, I recon I still think it worked out at about 2/3rd what I would have paid on the EBay.

Link to comment
Share on other sites

That's interesting. Auctions down here seem to attract high bidders. I've generally paid more, in the end, at auctions than on eBay. I suppose you have to balance the auction buyer's commission and the VAT on that against the fee-less buyer's transaction on eBay - and see which tend to work out best.

Link to comment
Share on other sites

I think it all depends on who's there on the day and how widely advertised the the lots are.

Definitely , i think it depends if the auction is online to , i struggle to buy anything through saleroom.com these days although did pick up a 9ct gold one last week as it wasn't listed as gold.

Love the SS Omega though very nice

Link to comment
Share on other sites

I use when time Watemans which is near Bluewater shopping complex . Viewings allowed on theThursday before the auctions. Normally the first Friday of every month. 

Sometimes good prices but sometimes absolutely stupid prices its all down to luck. I used to pick up good quality French clocks for £20 + commission. But prices have really fallen on eBay so don,t bother any more. However I do like the atmosphere some real characters there too.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • We still need to know what the movement is inside, then we can advise you. The calibre number is usually stamped under the balance cock.
    • @Deebee2024 I would advise not trying to clean the dial unless you are 100% sure it is fired enamel. Any other finish is likely to be severely damaged with any technique unless you’re extremely proficient doing dial restoration and really know what you are doing.   Tom
    • I'll give it a try an let you know 😅   I've accumulated quite a few lubricants for that reason... but in this particular case I'm a bit hesitant.    Yea, I really wonder. What's interesting, is that for calibre 918 (introduced in 1994), which seems to have the same rotor construction as the 916 (introduced in 1969), JLC recommends "immersing [the oscillating weight] in a mixture of benzine and 0.02% D5 oil" (is that basically what Lubeta V106 is??). So they didn't stick to 941..    
    • Interesting movement!   These appear to be similar ones on ebay, in somewhat better condition, if you need spares? https://www.ebay.co.uk/itm/294082407812 https://www.ebay.com/itm/335367737161   This video shows how to make a simple and reasonably safe rust remover - the recipe is in the video description. I've used it on various things with great success!    
    • A 1oz should be about right for most work. I had 4 all different as I was also a clock maker. I also had a box wood mallet. 
×
×
  • Create New...