Jump to content

Initial greetings

RoyC

By RoyC
in Introduce Yourself Here

 Share

Recommended Posts

RoyC New Member

RoyC

Posted
Posted

Hi. My name is Roy and I'm an amateur horologist aspiring to be less amateur. I'm in my 70s, groan.

I've collected (ie accumulated) modestly for decades. Nothing very exotic because my income has always been distinctly non-exotic. Though one of my closest friends I've also acquired a vast quantity of unsold parts, movements and complete watches. For the last few years I've been working through them, selling off the immediately usable items and gradually working my way though them, repairing at various levels of complexity  and difficulty. Lots of crippled  watches in my wake but it's getting smaller. Like most things in life you have to start out being very bad at difficult tasks, passing though the slightly less bad and approaching the not too bad if time permits - which at my age is a constant consideration. I wish I'd started on this path earlier however "if i knew then what I know now.... etc" is a refrain that most of us start singing if we live long enough.

I'm fortunate in that I have a good relationship with a horologist who does the more demanding work for me. We're also friendly so it's better than a purely commercial relationship. I try not to pester him too much for advice. I'm always in need of advice.

Mark's tutorials are simply outstanding - there's nothing else that I've seen on YT that even compares where this subject's concerned.

Roy

PS Anyone got a spare good LIP T18 balance kicking around that they don't need?  I have a good HS. Well, you gotta ask.......

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • VWatchie
      Epilame / Fixodrop

      By VWatchie · Posted

      You're thinking metal to jewel in general I guess. Maybe it would be a good idea to peg the pallet jewel hole on the main plate after the epilame treatment. I think that could work as it is my impression that the epilame doesn't sit very hard, but I could be wrong about that so feel free to educate me. I didn't remember that 9501 was thixotropic (thanks for the link). That would mean it's even runnier during impact (lower viscosity) so perhaps it's time I get some fresh grease as mine seems a bit too runny. What I have seen is a whitish surface after washing but it goes away if I scrub the surface with a brush in a degreaser (Horosolv). I don't think it embeds itself in the metal but sticks very hard to the metal. I don't worry too much about the cleaning solution. I just want perfectly clean parts and my solution can be replaced for little money (ELMA RED 1:9). Anyway, I quite often need "to strip back and rebuild" and scrubbing parts by hand isn't exactly the most stimulating part of a service.
    • rehajm
      Epilame / Fixodrop

      By rehajm · Posted

      I’ve had a couple movements where it is clear the previous watchmaker was diligent with lubrication but the old epilam had turned to a fine white powder covering the pallet fork and keyless parts, which can’t be good for parts. I’m spare with epi since I don’t know how long it takes to degrade to that state…
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      I have read some suggestions that it can cause wear , particularly on the fork horns of a fully treated pallet fork. I've had half a kilo of steriac acid powder on a shelf for almost a year now, might have a little play today with a heater and a jar.  I think its because it gets into their cleaning solutions Mike. Theirs or anyone else's that services the watch next time, or if they need to strip back and rebuild. Could preclean but thats all time for a pro. I thought the idea was for the epilame to create a barrier, a wall between the lubrication and anything else, so the lube cant spread.
    • mikepilk
      Epilame / Fixodrop

      By mikepilk · Posted

      As I'm only cleaning watches in small numbers at home, I pre-clean any significant deposits of old grease and oil before using the cleaning solutions. I scrape off deposits with pegwood and Rodico, and if really dirty, wash parts in naphtha with a brush.  So I'm happy using DX, but can understand why it's avoided by the pros.
    • Neverenoughwatches
      Any tips to correct a sloppy error?

      By Neverenoughwatches · Posted

      I think attaching a nut to the lid to pull it off is the least destructive, any damage damage on the outside is going to an easier fix than any created when trying to push it out from the inside. Scratching up the inside of the lid , mainspring or arbor bearing will be risk. Just my opinion.
×
×
  • Create New...