Jump to content

Recommended Posts

Posted

 Is it just me or does anyone else have a problem with Lemon Pledge?

Lemon Pledge seemed like a godsend. You could bring back the shine to dull furniture with just a quick wipe down. My last cleaning lady got her hands on a can of it and literally Lemon Pledged every wooden thing in my house.

But when you stop using it after a few years, the wood looks worse than it first started. I've tried cleaning it with detergent, Old English Oil, other brands of wood polish, even wd40. But the white, dried out look reappears after a short while. The only thing that restores the shine for a few more year is Lemon Pledge again. 

It was the same with Armor All.

I hate to be forced to continue using a product for the rest of my life.

20200507_100812.jpg

Posted

Try googling silicone oil in wood finishes as I suspect that that is the culprit.

It is what produces that instant glossy shine so easily on just about any surface but from what I understand it can cause problem if it gets through the original finish and into the wood and then you get this effect.

You may be able to break the tie to Pledge just by finding another furniture polish with silicone oil in it, but if you want break the tie with silicone oil then you will probably have to refinish the wood.

Posted

A wax polish is best if you want a more permanent finish on your furniture. You also need to consider the type of wood you are going to polish. Wax needs to build up, so you won't see good results  right away. Pledge and alike is only good on modern furniture

Posted

For restoration, I use Briwax applied with 0000 wire wool. Stinks to high heaven but the results are worth it. (Best after a light rub over with white spirit.)


Sent from my moto g(6) play using Tapatalk

Posted (edited)

You might also try a little heat. Sometimes the issue is that moisture gets sealed in behind the finish because the silicone acts as an impermeable barrier. Gently heating with an iron on a cotton cloth (don't use synthetic material) may drive out the moisture. Alternatively, you can try alcohol. Be very careful that you don't make things worse.

 

Finally, try to avoid silicone based polish/cleaners, they are a pain. Stick with beeswax if you can.   They take more work, but they are far more forgiving and easier to fix when you get problems.

Edited by AndyHull
  • Like 1
Posted

What is going on depends on what the finish is that's doing it. Most furniture built since probably the 70s is going to have a polyurethane finish on it. It's essentially a coating of plastic, and when plastic breaks down it gets chalky like that. Plastics, as we all know, don't like oils, lemon Pledge has lemon oil, bam! Chalky. Unfortunately, there's not a ton you can actually do. All of the poly on that wood has been subjected to the same treatment. If you were to brush off the chalkiness with a stiff bristle brush and put something over it, the rest will continue to chalk up underneath before you know it. Refinishing is about your only option for a real repair.

Short of that, assuming you don't want to go through the hassle or expense, brush off what you can of the chalkiness with a stiff nylon brush. The wax suggested above will help, but it's not permanent. Wax is soft, stays soft, and will come off with wear, which is why it needs to be constantly reapplied. Traditionally, "wax" is something like 25% beeswax 75% oil, so you have that oil problem again. Still, you're already hooped, and it'll look reasonably nice for a while, so...

Another option to consider may be a drying oil. A light coat of boiled linseed oil might seal things up in a lower maintenance fashion. Wipe on, wipe off; you want the barest, thinnest coat since it'll likely only adhere very well to the rough stuff. It's oil still, but it quickly polymerizes and hardens. It'll still chalk up underneath over time, and maybe even quicker than it would with the wax since you wouldn't be rubbing off the chalkiness with subsequent applications, but it's one and done.

Finally, the watchmaker's favorite, shellac. Shellac will go over just about anything. It'll seal things up nicely, if you use the blonde stuff it won't affect the color, and just a light coat or two will just barely up the gloss. It'll still chalk underneath, but that's kinda what you're stuck with at this point.

Posted

Thank you very much for all your answers. But resistance was futile. I went back to using Pledge because I still have a large can of it.

I bought the can while restoring an antique longcase clock. The owner must have used Pledge in the past. Whatever I  used, furniture polish, furniture wax, etc, just wouldn't work. It may look good right after I polished the wood but a few days later the white, moldy appearance returns. 

I found that Pledge was the only product that that could give a lasting shine. It appears that once an item has been Pledged, nothing else can fix it. So.... NEVER apply Pledge to wood if it has never been Pledged before.

  • 4 years later...
Posted

I had the same experience with Lemon Pledge on my garden furniture. It worked great at first, bringing back the shine and making everything look pristine, but after a while, the furniture started looking even worse than before. It's like it left this weird dried-out white residue that just never seemed to go away, no matter what I tried.

Posted
On 10/9/2024 at 1:44 AM, Staceyanom said:

I had the same experience with Lemon Pledge on my garden furniture. It worked great at first, bringing back the shine and making everything look pristine, but after a while, the furniture started looking even worse than before. It's like it left this weird dried-out white residue that just never seemed to go away, no matter what I tried.

I even used Old English Oil and some other wood care products, but nothing worked as well as Lemon Pledge—until it wore off again. It feels like I'm stuck in this cycle of needing it forever!  source: just my own frustrating experience! It’s frustrating to rely on something that makes you feel like you're just patching it up.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hello and welcome to the WRT forum.
    • interesting video nice to see the machine what it can do now I wonder what it costs and I'm sure it's not in my budget. Plus the video brought up questions but the website below answers the questions? What was bothering me was the size of his machine 4 mm because I thought it was bigger than that? But then it occurred to me that maybe they had variations it looks like four, seven and 10. With the seven and 10 being the best because way more tool positions in way more rotating tools. Although I bet you all the rotating tools are probably separate cost https://www.tornos.com/en/content/swissnano   Then as we been talking about Sherline. Just so that everyone's aware of this they have another division their industrial division where you can buy bits and pieces. I have a link below that shows that just in case you don't want to have the entire machine you just need bits and pieces. https://www.sherline.com/product-category/industrial-products-division/   Let's see what we can do with the concept I explained up above and bits and pieces. For one thing you can make a really tiny gear very tiny like perhaps you're going to make a watch. Then another version the center part is not separate it is all machined from one piece. Then fills gear cutting machines have gone through multiple of evolutions. A lot of it based on what he wanted to make like he was going to make a watch unfortunately eyesight issues have prevented that. Another reason why you should start projects like this much sooner when your eyesight is really good or perhaps start on watches first and then move the clocks then local we have from the industrial division? Looks like two separate motors and heads. Then it's hard to see but this entire thing is built on top of a much larger milling machine as a larger milling machine gave a very solid platform to build everything.   Then like everything else that had multiple generations are versions the indexing went through of course variations like above is one version and the one below was the last version. Now the version below I mentioned that previously and somewhere in the beginning to discussion and somebody else had one in their picture. As it is a really nice precision indexing. Then I wasn't sure if I had a the watch photos here is his unfinished watch. No he wasn't going to make a simple watch like none of his clocks were simply either what would be the challenge and that.    
    • Use a Portwest Howie lab coat. They are the biological type so they have tapped cuffs so you don't end up getting the loose cuffs of normal lab coats catching everything. 
    • Some of the Chinese tools ae great and can be purchased at a fraction of the price of Swiss ones, some are complete garbage and some I'm convinced are coming out the same factory as the branded ones.
    • I found this string about this problem. I've not gone through it all, but I believe it also mentions making a spring. If not in this string, the info is online.
×
×
  • Create New...