Jump to content

Fitting a watch crystal

Alaskamick

By Alaskamick
in Watch Repairs Help & Advice

 Share

Recommended Posts

Alaskamick WRT Addict

Alaskamick

Posted
Posted

Hello again. Following my request for help finding a watch back the only option seems to be fitting a low dome crystal instead so the back becomes see through, curtesy of philipk5

My question is how much bigger than the actual size of the hole should a watch crystal be to ensure a tight fit but still fit in.

The diameter measures 27.8mm and as it's only a cheap watch which I want to fix as usable for my son but I don't want to spend loads of money buying a range of sizes.

Any advice would be appreciated.

Thanks, Mike

yankeedog Distinguished Member

yankeedog

Posted
Posted

I have always heard that it should be the same size as the opening, But in my adventures I have found that the same size is sometimes a bit small.Sometimes spot on.If you go the next oversize its usually a safe bet.

  • Like 1
yankeedog Distinguished Member

yankeedog

Posted
Posted

If you still find it loose and you need it to stay put.....on a cheap watch....just a tiny bit of super glue applied to a well cleaned oil free case..three or four tiny spots..so you wouldn't notice it.and the crystal will stay in place .

  • Like 1
philipk5 Member

philipk5

Posted
Posted

If the internal diameter of the case measures 27.80mm then a 28.00 low dome acrylic should be able to be fitted using a "claw". It needs to be tight enough to provide some sort of seal and not fall out but not so tight it won't fit!!.

If you use any sort of adhesive it will make removing the acrylic somewhat difficult in the future (probably next week when a proper case back turns up). 

Also make sure that the crystal doesn't foul the stem &/or pushers and any moving parts.

Photos of your watch front & rear may remind someone they have something in their scrap bin?

Hope this makes sense, and helps keep another watch in use.

Cheers

Phil.

  • Like 1
eezy WRT Addict

eezy

Posted
Posted

A simple cheap alternative would be to make a case back from a CD (Compact Disc)

I have a habit of stringing up CD's in the garden. After they have weathered the coating comes off and they are clear but not as transparent as a watch crystal. Also the ones I have had are 2 part laminates which easily separate after weathering. I have used these in the past for emergency crystals in cheap watches.

In this case you could use a new CD. Cut out a circle which fits tightly into the case. Cut another circle which fits over and to the overall diameter of the case and glue the 2 together. Alternatively just cut a circle which fits the overall diameter of the case and glue it on but glue it all around so to seal it. Trim if necessary with a file, sandpaper etc.

It should not scuff up as quickly as a crystal. I use scissors to cut after the CD has delaminated ie one half but I use my scroll saw to cut a full thickness CD

JerseyMo Distinguished Member

JerseyMo

Posted
Posted
3 hours ago, Alaskamick said:

Hi JerseyMo, It's a snap back.

you may than have to measure the inner dimension of the crystal if there is a lip.  Either way it goes I would not recommend the use of any adhesive.  

  • Like 1
vinn3 Distinguished Member

vinn3

Posted
Posted

   the use of glue, on the crystal, will reduce the value of any watch!  if you must use it,  use epoxy,  on the bezel, because it can be removed easily  with 200 degrees farenheight.    there are many instructions on proper "crystal replacement".  vin

Nucejoe Distinguished Member

Nucejoe

Posted
Posted

If you have the dimensions I can have a crystal custom made to any profile or flat, costs are at most two euros.

I also have abundance of desent european quality vintage NOS flat crystals at low price.

Cutting is done with grinding stones.

To alter one and make fit yourself. Use a razor blade to shave off the circumference down to a perfect fit. 

The art of perfect fit is patience.perfect fit gathers no or minimun dirt. 

The diameter is to be 2/100 of a millimeter larger for tight fit.

If polymer try heating the case , insert the crystal, keep under press, raise tempto get the polymer melt fit. 

A good press insertion dose a lot of good for flat crystals.

Regards joe

 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Curare
      Bracelet Extender Sizing

      By Curare · Posted

      Thanks for that Andy, Yes the new bracelet is worth more than the watch itself, Its one I have bought to service and clean-up and on-sell it as a project, look it may sell to someone who has a small wrist, I think I will buy an extender and may-be offer it up with a normal strap as well CJ
    • JohnR725
      Unknown watch movement logo. Very interesting

      By JohnR725 · Posted

      Not always that simple. Typically the only reason we would have any way of identifying a watch is if parts were available at any time and somebody had a parts reference book then they would help you to identify the watches that they have parts or. Unfortunately there are hundreds of thousands of watch movements with no identification and of course typically no parts the classic place were watches would be identified would be under the balance wheel and your pictures don't really show a good view of that. Occasionally I've seen watches marked under one of the plates. They felt very proud of their watch is a very prominent Swiss company and they ask he stamped the bottom of a plate so you have disassembled find it. Then there is the other system the keyless parts make up something called the fingerprint system but you still haven't given us enough information to make use of that. Here's an image showing what a fingerprint system looks like. The PDF is based on the physical book the physical book has sizes of watches these are smaller ladies watches and keyless parts which in the physical book are printed at the actual size of the watch parts. So to identify with the keyless we need in your case diameter measured on the dial side and a good picture of the keyless parts and then you have to hope that this was made within the right time span of the books that have this system on the other hand a lot of times on the dial side they will also put markings. So basically to identify a movement it has to come out of the case and has to be disassembled.
    • AndyGSi
      Bracelet Extender Sizing

      By AndyGSi · Posted

      The strap is a 44Q6JB and hadn't realised how much they'd gone up in price. The used one I've got is very worn but may have other links floating around.
    • mbwatch
      Full plate watch, Suitable tool for adjusting & testing pallet stones?

      By mbwatch · Posted

      @Mercurial is this also a variation of the tool you posted? 
    • Curare
      Bracelet Extender Sizing

      By Curare · Posted

      Thanks Andy, The bracelet is sized very small, around a 14cm wrist. Were would one try to source original links, I guess they wouldn't be cheap if found. The bracelet end links have 4406 B-E stamped on them, is this the Seiko Bracelet code ?? CJ  
×
×
  • Create New...