Jump to content

Can you install an armored crystal without the claw tool ?

Chopin

By Chopin
in Watch Repairs Help & Advice

 Share

Recommended Posts

qhartman Watch Enthusiast

qhartman

Posted
Posted

I've always done acrylic crystals (both tension ring and interference fit) with a crystal press. I have one of the "claw tools", but I've never had success with it. Even on high dome crystals, it slips off before putting enough pressure on the crystal to pop it out.

Sent from my ONEPLUS A5000 using Tapatalk

Link to comment
Share on other sites
Chopin Super WRT Addict

Chopin

Posted
  • Author
Posted

My press never works with acrylic crystals. Any tips ? They just won't go in.

In the past I would remove just a tiny bit of material from the edges (without leaving a mark, obviously) and it would go in the slot.

Link to comment
Share on other sites
qhartman Watch Enthusiast

qhartman

Posted
Posted

I always use a cupped die that puts pressure right at the edge of the crystal. It can be tricky to get everything lined up, but usually after one press I find that most of the crystal is in. Then, I rotate the case with the crystal and press repeatedly until I got the sweet spot that gets the rest to snap in. I'm not sure if my press doesn't quite press evenly or what, but this technique works consistently for me, and I haven't cracked a crystal yet. I do press harder than it feels like I should be.

Sent from my ONEPLUS A5000 using Tapatalk

Link to comment
Share on other sites
noirrac1j Distinguished Member

noirrac1j

Posted
Posted
2 minutes ago, qhartman said:

I always use a cupped die that puts pressure right at the edge of the crystal. It can be tricky to get everything lined up, but usually after one press I find that most of the crystal is in. Then, I rotate the case with the crystal and press repeatedly until I got the sweet spot that gets the rest to snap in. I'm not sure if my press doesn't quite press evenly or what, but this technique works consistently for me, and I haven't cracked a crystal yet. I do press harder than it feels like I should be.

Sent from my ONEPLUS A5000 using Tapatalk
 

Perfect.

J

Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted

I do some overflow work for a watchmaker friend. He's Omega factory authorized and all that. On the odd case (oddly enough often omega) I just can't get the armored crystal in. Stop by his place, and he has 100% succes rate. His method is two-fold. 1-He has a large flat pusher in his press, and he lays the conical die on the crystal and the presses it with the flat pusher. 2- he rubs his finger on the side of his nose, then on the perimeter of the crystal. That little bit of "nose grease" makes a huge difference.

Of course a micro smear of silicone would work too but it's sooo messy.

Link to comment
Share on other sites
chrisdt WRT Addict

chrisdt

Posted
Posted

Perhaps its the time to mention tension ring crystals. I've never been able to fit the ring inside the standard crystal even although  the crystal fits perfectly without it. I have a few Tissots including front loaders and all seem to have tension rings. I have seen special crystals with a gold or silver ring included but at a a prohibitive price. Is that the way to go ?  I have fitted quite a few without the ring and used a tiny smear of cement and got perfectly good results. Hardly notice its not there unless you look at a certain angle...

Link to comment
Share on other sites
rodabod Distinguished Member

rodabod

Posted
Posted

The tension rings provides... well, additional tension and therefore waterproofness.

It’s important also when you want the watch to look original as sometimes the tension ring is sized specifically to suit the bezel and dial. 

Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted
Perhaps its the time to mention tension ring crystals. I've never been able to fit the ring inside the standard crystal even although  the crystal fits perfectly without it. I have a few Tissots including front loaders and all seem to have tension rings. I have seen special crystals with a gold or silver ring included but at a a prohibitive price. Is that the way to go ?  I have fitted quite a few without the ring and used a tiny smear of cement and got perfectly good results. Hardly notice its not there unless you look at a certain angle...
Tension ring and armored are the same thing. They typically come in white or yellow and generally work well on the vintage watches they mostly are used on.

On some pieces like chronogrphs the tension ring is also printed, which can be troublesome if a genuine replacement isn't available. If lucky a generic armored crystal can be adapted, this usually involves some lathe work.
Link to comment
Share on other sites
chrisdt WRT Addict

chrisdt

Posted
Posted

So to sum up on tension rings am I right in saying that when renewing a flexi glass crystal with a tension ring I have to buy the new crystal complete with the appropriate coloured ring and not be able to use the old ring with a standard crystal?

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      So leave off the seconds. Stand the movement on its edge, its the dial edge that rests on the pad ( either rubber or cork , something that wont slip ). Use a finger of your left hand to hold the movement upright,  right hand presses the release and flicks out the stem. I do it this way so i can see what I'm under a microscope. But you could hold the movement between two fingers of your left hand, its the right that has to manipulate the stem out by pushing the release and flicking out the stem with  right ring finger nail. Sounds more complicated than it actually is. I guess you could fix a push pin to something solid, then all you need to do is push the release against the pin, leaving your right hand completely free to pull the stem out.
    • HectorLooi
      Battery

      By HectorLooi · Posted

      Try putting everything back together and closing the back cover. I think one of the two springs has to contact the metal casing to ground the casing. So when you press the button, it will touch the contact on circuit board and close the circuit.
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes, the seconds hand is the longest and goes almost to the edge of the dial. I can’t quite picture it how you do it on the rubber pad
    • Murks
      Battery

      By Murks · Posted

      A don't think so it leaked or damaged it because the watch itself works it just the buttons ain't working not connecting with the circuit board have taken more pictures of where the buttons makes contact with the circuit board.
    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      I think what peter means oh is once he has fitted the hands and  checked for  alignment if them and that they dont foul, how does he then hold the movement to remove the stem in order to case up. The dial cannot be laid on a cushion or in a movement holder as the hands will get damaged. This can be quite tricky for a beginner, what i do is  to stand the movement on edge on a rubber pad so it doesn't slip. Hold the top edge with one finger then my dominant hand uses 3 fingers to press the stem release and flick out the stem. See below peter, leave off the second hand as this is the longest and gets caught the most, then fit it once the stem is out. Alternatively place the movement in one of the cup style holders, i imagine this is what they are designed for. They only touch the very edge of the dial.  
×
×
  • Create New...