Jump to content

What is it called? Hairspring Pin/Stud/wedge/plug...

StringyBob
 Share

Recommended Posts

StringyBob New Member

StringyBob

Posted
Posted

Hi - I have a few old wristwatches, I'm transplanting the hairsprings from donor watches. They all have small brass pins/wedges pinning the outside end of the hairspring into the balance cock 'stud'. 
This seems to be a fiddly job and I've managed to lose 5 of the pins so far (all sent flying to the four corners of the room, never to be seen again!). So I'm out of pins now.

I presumed these would just be called hairspring or regulator 'pins', but I see on the web that regulator 'pins' can also refer to the 2 vertical 'pins' on the regulator that the hairspring travels between.

So my question is simple - what are these little brass pins/wedges/plugs actually called so I can buy some (various sizes)?

I contacted CousinsUK to see if these might be correct 'https://www.cousinsuk.com/product/hairspring-collets-pins-wristwatch?code=S37391', but they seemed to know less about the product than me! There reply was 'We have followed up your query, however unfortunately the information you have requested is not available. All the information that is available is already on the website....'

As I mentioned I need a variety of sizes (diameters) if possible.

Thanks

  • Like 1
Link to comment
Share on other sites
StringyBob New Member

StringyBob

Posted
  • Author
Posted

Thanks for that. I've just been searching some more on CousinsUK and found something called 'Hairspring Fixing Pins', which seem to be exactly the same as the 'Hairspring Regulating Pins' I mentioned above (same code number, photo etc)... so I guess it must be those. I'm surprised Cousins Support couldn't tell me that though.
Thanks again

Link to comment
Share on other sites
RyMoeller Super WRT Addict

RyMoeller

Posted
Posted
19 hours ago, Marc said:

I did a little write up on the easiest approach to this before.

https://www.watchrepairtalk.com/topic/3335-my-post-christmas-challenge-picture-heavy-cos-i-knows-you-like-em/#comment-52962

Ah, the write-up regarding taper pins is wonderful- thanks!  I tried a few times to turn a replacement on the lathe and discovered it was nearly impossible to turn one narrow enough from brass; so I cheated and turned one from steel (fear not, the pin is installed in my daughter's Cinderella watch).

Link to comment
Share on other sites
dadistic Distinguished Member

dadistic

Posted
Posted

The assortment of hairspring fixing pins should give you what you want. They are used to attach the collet  as well as the stud. I have some that I've acquired  from various sources, but I think the next time I don't have what I need I'm going to follow @Marc's  instructions and make my own.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Mercurial
      Smit

      By Mercurial · Posted

      We need to identify the movement to help you, but the oldest of these Rolco watches use Aegler-Rebberg movements that lack a calibre number and are very difficult to identify. You may end up having to make or modify a stem to fit . Post pictures of both sides of the movement when you have it and the size of the movement and hopefully it’s one that has a calibre number.  Gruen used a lot of the same Aegler movements at the time and it’s worth comparing your movement with those if you can’t find it labeled as an Aegler or Rolex/Rolco calibre. Best Regards, Mark  
    • Neverenoughwatches
      Winding pinion making

      By Neverenoughwatches · Posted

      Onlly a pro's eye would notice that OH, you've still got it old fella 🙂
    • Mercurial
      How to remove shock settings from Smiths 512 movement

      By Mercurial · Posted

      The triple lobed spring, as you suggest needs to be rotated to remove it or replace it. Suitably shaped pegwood should suffice, but tools (shaped as you describe) for the purpose also exist.  If you have an assorted of replacement springs, a trilobe style KIF spring of the right size might fit.  The other spring securing the jewel also needs rotating. There is a slight opening in the setting at about the 5 o’clock position in your photo and one side of the spring should be able to be removed  there when rotated into position.  Hope that helps, Mark
    • RobS
      How to remove shock settings from Smiths 512 movement

      By RobS · Posted

      As an update, it transpired the setting on the balance side, with the jewel had one flat end and one curved. When I rotated it enough it popped out. The chaton was entirely conical and a tricky customer but once lubricated and dropped back in I put the flat edge in first and poked it in with the peg wood tool mentioned above (I made it with flattening off the end then sizing with a pencil sharpener before poking a hole in the end) then rotated and it went in well.    For the other side, magnet searching for the spring has been fruitless.    thanks for the link to the other thread
    • Rustinbox
      Omega Split stem issue (will not go back in)

      By Rustinbox · Posted

      Thank you. It didn’t look rusty. For sure old.    Female part was inside the movement, and when I pushed male part, it got broken. I didn’t apply grease. Here is the photo.      Could it be that male part is too thick for some reason?
×
×
  • Create New...