Jump to content

Watch Crystal Polishing


Recommended Posts

Is it possible to get scratches out of a Seiko Hardlex Crystal. I tried with a drumel tool and various types of polish but was unsuccessful. Polishing the body of the watch works well, but the darn crystal scratches stay. You would think that making a scratch is less violent than 5000 rpm drumel with #2 polish.

From Canada

Link to comment
Share on other sites

I think Hardlex clouds with the heat of the dremmel...too fast, too hot! By the time you "eliminate" the scratch the crystal will be unusable. A slower "way/machine" with gradually decreasing grids and, using a coolant, might work though.

Link to comment
Share on other sites

It can be done as I did one for my 6139B for which new Seiko crystals are hard to come by a very expensive.  Just needs plenty of patience and work through the wet&dry papers, then diamond pastes to get the final polish.  Mine took about 4 hours in total so maybe not cost effective for a pro.  

I got about halfway through and decided that as it was a nice sunny day (1 one we had last year) I would continue on the patio.  You guessed it, just about to give it a final polish when I dropped it, and yes it broke into 3 pieces.  I nearly cried !!  

Just had to cough up for a new one but settled for a Sternkraus which was a perfect fit.

Edited by canthus
  • Like 1
Link to comment
Share on other sites

I have polished one yesterday, no big dial. Speed can be 6 - 10K, doesn't matter much, paper quality do matter. I've found that most effective is 3M 600 grit, wet of course. Finish with 2000 and if you have it diamantine paste.

 

25563826375_5a6457681b_c.jpg

 

One or two darn specs of dust have dodged my attention and I'll remove them tomorrow.

Link to comment
Share on other sites

I have polished one yesterday, no big dial. Speed can be 6 - 10K, doesn't matter much, paper quality do matter. I've found that most effective is 3M 600 grit, wet of course. Finish with 2000 and if you have it diamantine paste.

25563826375_5a6457681b_c.jpg

One or two darn specs of dust have dodged my attention and I'll remove them tomorrow.

Did you use a Drumel tool and some sort of bit?

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

Did you use a Drumel tool and some sort of bit?

 

Rotation speeds implies a rotary tool of your liking and wet paper about 6cm diameter. People saying it can be done manually just love to see their life being ground slowly.

Edited by jdm
Link to comment
Share on other sites

If you had kept going with the 2000 grit before the final polish you would have removed all the marks from the 240.

I did finish with the 2000 grit but did a final buff with Peek. I think a piece of leather would work as the final final buff

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

I did see some very fine scratches if I looked at a light through the Crystal. I'm pretty picky so I did do a rebuff with the drumel and some fine Green #7 polish. Looks pretty good now. Like new. Now I don't have to disassemble the Crystal assemble including Gaskets etc.

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites

Awesome video dude!! Exactly what I was looking for in terms of polishing info!

Thank You

Sent from my iPhone using Tapatalk

Hey thanks. The video I did is what I was looking for all along. I have a ton on YouTube music and some magic videos but now am adding Watch Repair instruction where I can and only if it works. Mark is the man when it comes to the watch repair game. I am one step below amateur. You can find me on Facebook as well under JDWatchboy. I put up the site to track progress on some watches I am fixing for friends and for part costs only. Just enjoying the hobby, but who knows?

Sent from my iPhone using Tapatalk

  • Like 2
Link to comment
Share on other sites

Ok, revised advice. I took the Crystal once again as there were two small hairline scratches that were just bugging me, and tried to remove them using pumice. That made it worse. Then I used my drumel again and tried to buff out the new scratches; that didn't work. Then I got out the 1200 grit and worked a full sheet of rubbing followed by the 2000 grit and a half sheet of rubbing; THAT WORKED! So new technique should be Drumel with 240 grit drum for the first shooting and major scratches followed by a quick drumel buff with number 6 High Gloss, followed by 1200 grit, Two Sheets of hand rubbing and 2000 Grit 1 sheet of hand rubbing (sanding). DO NOT GO IN CIRCLES while rubbing; back and forth is best. Thanks.c57d3bc465bd728e67c60a8688664877.jpgc80a5f8af13ad56d65617b4a571299ad.jpg

Sent from my iPhone using Tapatalk

  • Like 1
Link to comment
Share on other sites

i gotta tell you that is an excellent job. it looks like a new crystal. i just purchased a seiko diver that needs a lot of help with the crystal. i am actually gonna buy a new one, but i'd be interested in trying this method on this crystal. the diver i got has quite a few deep scratches that i think might not polish out.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • While you might have seen it as a humorous/Dramatic remark was done very deliberately so I could get an answer. Let me quote myself? The simplistic of this entire discussion is the group would like the last forever.   If you go to the top of the discussion group you'll find something to click on that says staff. Then you click on Mark's name and you find out interesting things? For instance he was last here on Saturday so yes he is here. If there is a crisis or a problem he is going to be here. You will also find a list of his activity although that's only the public activity. There's a lot of work that goes into running message boards and he probably does a lot of stuff in the background that we don't see to keep it going. Unfortunately message boards do not run themselves. Then regarding this did you notice you can message Mark and ask him. Then if somebody, we could elect somebody from this discussion such as @Neverenoughwatches To reach out I would really keep the message super simple like? You could refer him to this discussion but I would really keep it simple Like for instance the group enjoys his message board and what could we do to keep it going Forever? Then regarding all of the other suggestions comments helpful remarks or ideas? When was the last time any of you bothered to read the message board rules? This is covered which is one of the reasons I did the dramatic things I did to provoke a response of the basics as opposed to starting to suggest or seemingly suggesting all sorts of ideas which are covered by one of the rules found in the section on rules. In other words I'm going to quote something from the rules of the message board.  
    • For me any input from Mark would be great. If he's keeping a close eye i would imagine he has read about our concerns here. But specifically i would like to know if he is ok with us collecting each others contact information for those of us that wish to provide them. 
    • Hello and welcome from Leeds, England. 
    • Thank you!   Yes I did. I did not notice a difference. Although 9415 is advertised as a thixotropic grease (and I did had high hopes for it), the only advantage at this point I see is that its “easier” to apply than an oil (if one does not use epilame). But this is subjective, I guess. What I did notice though, if you apply a bit too much grease, that definitely slows down the movement. Oil in this case is a bit more forgiving, as its super thin, and it would usually just spread out.  Again, imho.
    • Mark keeps a close eye on his forum. I'm sure if you asked him he will reply, he might not do it right away but you will receive his answer.  
×
×
  • Create New...