Jump to content

Need New Stem / Crown For Old Swiss Army Cavalry Watch


Jso

Recommended Posts

Hello, I'm new here. Never repaired a watch before but hope I can muddle through this one . I imagine a professional repair would cost more than the watch is worth. The stem on this watch broke. I have both pieces. I removed the remaining piece of stem from inside.( took forever ) The movement says Ronda, but no numbers. I think the crown might be permanently attached or at least very tight.

I really like the watch and hope someone can help me fix it. Thanks!

Link to comment
Share on other sites

It appears to be a Ronda 515 typical in those Swiss Military watches. The stem is one piece and you need a pin vise to hold the remaining piece of stem and this way unscrew the crown (recover it). You will also need a new stem for this movement or an extender if it fits in the tube. You will need a stem/wire cutter, caliper, sanding stone/diamond to fit the new stem (or extender) and don't forget to dip in Loctite 222 (not a glue) the stem portion that goes in the crown. I also, once everything is fit and ready, lube the inside of the crown (the gasket) with silicon grease and lube with the appropriate oil the tip of the stem.

 

Search Geo's excellent "how to" for the stem fitting technique.

 

Cheers,

 

Bob

Link to comment
Share on other sites

Just ordered the stem and a pin vise. I'll assume that if the pin needs to be trimmed, I do not cut the threaded end.

Thanks again. What a great forum!

 

Actually it is the threaded end (that pokes out of the side of the watch and screws into the crown) that you DO cut.

The other end which goes into the movement is specially shaped to connect into the setting works, so if you cut that off it won't work at all.

Link to comment
Share on other sites

It appears to be a Ronda 515 typical in those Swiss Military watches. The stem is one piece and you need a pin vise to hold the remaining piece of stem and this way unscrew the crown (recover it). You will also need a new stem for this movement or an extender if it fits in the tube. You will need a stem/wire cutter, caliper, sanding stone/diamond to fit the new stem (or extender) and don't forget to dip in Loctite 222 (not a glue) the stem portion that goes in the crown. I also, once everything is fit and ready, lube the inside of the crown (the gasket) with silicon grease and lube with the appropriate oil the tip of the stem.

 

Search Geo's excellent "how to" for the stem fitting technique.

 

Cheers,

 

Bob

Hello!

 

Is it Loctite 221 or 222? I don't want to correct you, I just want to be sure.

 

Thank you,

Bogdan

Link to comment
Share on other sites



  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Yes i did eventually realise that the oil will act as a barrier, I'm sure the discussion will continue. Ive had two oleophobic coffees ( added coconut ) and in the meantime i have this just delivered to take my mind off epilame for the time being. My favourite type of dial, its a beautiful looking watch traditional English made and it runs,  the ticktock is phenomenal,  i can hear it across my living room .  You wont believe how much it was. Thats interesting about synthetic oils , i thought the same, going from a 2 year service to 5 years is a big drop in income for service folk.  I expect some did well when they embraced the use of synthetic,  probably drawing in more customers than those that didn't use the new fangled substances , i bet fairly short lived though. The more frequent service makes more sense to me, not for just the service but for the regular check up inspections that might pick up impending faults. As far as epilame goes, wouldn't it be great to be able to fumigate the complete movement in a sealed jar of heated stearic acid, 🤔 now theres a thought 😅.
    • Imm going to close the discussion by attaching the photo of my super-titanium after several vicissitudes finally working. Purchased as not working I replaced the battery and for a stroke of luck I found its semi-new solar panel which, having verified its operation, seems to recharge the accumulator perfectly. I had taken this watch almost by bet, with 40 euros I brought it back to life. The initial half idea was to resell it to finance another purchase, but.. it's definitely a nice item. It would need to check the impermeability but it's a pleasure to see it on the wrist 😃
    • In fact the secret is to go gently and find the way without forcing, and the movement enters without problems
    • Yea a have given it a full service this movement is chinese 2813 whats the lift angle for this movement does anyone knows  and how  do a remove the default  of 52 degrees on my timegrapher?   Hi you said my lift angle is default how do a remove this from my timegrapher?
    • Sure! Some very accomplished repairers never use epilame! I have often wondered if it is worth the trouble. Not using epilame will shorten the service intervals though, but that could be better perhaps both for the owner and the repairer!? Speaking of oiling, I just read this: After WWII in the 1950s the first Synthetic Oils came on the market. Most watchmakers did not rush to use these oils since they were bad for business now that the watch serviced with Synthetic oil would not come back to him for service for another 5-7 years he would lose a lot of income. ~Ofrei.com   Anyway, I wouldn't be surprised if it would be more correct to think of epilame as a binder rather than a repellant. Until convinced otherwise that's how I will think of epilame.
×
×
  • Create New...