Jump to content

Omega 268 Service And De-Rust


Recommended Posts

This nice Omega came in with a seized up keyless work. The crown could not be pulled out to hand set position and the watch could not be wound. I immediately suspected rust.

 

post-1-0-79408000-1434120312_thumb.jpg

 

Getting the movement out of the case was a challenge because the crown could not be pulled out. But luckily I could unscrew the crown from the stem as the stem was seized.

 

post-1-0-77738100-1434120383_thumb.jpg

 

With the movement out of the case, I can see evidence of rust. Time to get stripping (the watch).

 

post-1-0-86805100-1434120404_thumb.jpg

 

First challenge was unscrewing this dial screw which was rusted in place. A bit of oil and some gentle persuasion and it unscrewed.

 

post-1-0-96740700-1434120464_thumb.jpg

 

With the dial off I can see the extent of the damage which is quite bad - but not the worst I have seen.

 

post-1-0-34487700-1434120558_thumb.jpg

 

post-1-0-92841300-1434120558_thumb.jpg

 

Off with the hour wheel:

 

post-1-0-35959700-1434120559_thumb.jpg

 

And the setting lever spring:

 

post-1-0-88232800-1434120559_thumb.jpg

 

post-1-0-09006900-1434120648_thumb.jpg

 

And this is as far as I could get. That stem was not coming out, but I have an idea! ...

  • Like 7
Link to comment
Share on other sites

Well I decided that the first thing to do would be to dismantle the rest of the watch - can't risk damaging any parts.

 

But first I drowned the stem and winding pinion with clock oil so it could start soaking.

 

post-1-0-12449100-1434128309_thumb.jpg

 

Then out with the balance...

 

post-1-0-65217300-1434128309_thumb.jpg

 

Then off with the ratchet wheel - does not seem to be any power there but I can't risk it so it's a good idea to remove the ratchet wheel and click work altogether. I don't like the ring of rust around the barrel arbor bearing...

 

post-1-0-14134100-1434128310_thumb.jpg

 

And the crown wheel... 

 

post-1-0-66540200-1434128310_thumb.jpg

 

Now I am sure there is no power on the mainspring (but I was wrong) so I can remove the pallets...

 

post-1-0-14597300-1434128311_thumb.jpg

 

Off with the barrel bridge and surprise surprise... more rust :(

 

post-1-0-63530800-1434128311_thumb.jpg

 

post-1-0-69579100-1434128312_thumb.jpg

 

post-1-0-17730700-1434128313_thumb.jpg

 

Not looking good - but it seems to be surface rust so it should come off easy. Now to open the mainspring barrel. Remember I told you I was confident all the power was released? I was wrong:

 

post-1-0-67490400-1434128313_thumb.jpg

 

Yes - the barrel arbor was seized in the barrel and so the spring was stuck in a fully wound position!!! I have never seen that before. Time to improvise. 

 

I thought the safest way would be to put the barrel in a polly bag and push the arbor with my fingers. That way nothing flies across the room :)

 

post-1-0-15454500-1434128314_thumb.jpg

 

And that seemed to work well.

 

post-1-0-15741600-1434128843_thumb.jpg

 

With the tension off I am able to get the arbor out and inspect it. It's a bit corroded...

 

post-1-0-70011900-1434128917_thumb.jpg

 

 

More to come...

  • Like 2
Link to comment
Share on other sites

Mark, Geo will lend you his Bergeon Basher!

attachicon.gifScreenshot_2015-06-12-16-15-21.png

 

I understood that Geo broke that opening a pocket watch :D

 

 

Interesting . How are you going to get that of ? Heat ? Oil ? 5-56? Coca-cola? 

 

A mixture of both as it turns out.

 

Soldering iron?

 

Now that's a good idea - I hadn't thought of that.

  • Like 1
Link to comment
Share on other sites

So next off is the main plate exposing the wheels. I was half expecting to find rust in the pinion leaves or pivots but all seems fine.

 

post-1-0-53034800-1434132332_thumb.jpg

 

post-1-0-44123400-1434132333_thumb.jpg

 

Off with the wheels...

 

post-1-0-95838400-1434132333_thumb.jpg

 

A teeny bit of rust on the escape wheel pivot but luckily not attached - brushed off and left no stain.

 

post-1-0-43877700-1434132334_thumb.jpg

 

Now back to this bugger of a stem. The oil did not seem to help...

 

post-1-0-49280800-1434132336_thumb.jpg

 

But after heating it up with my spirit lamp, I grabbed it with my pliers and gave it a sharp pull. It came away just fine. 

 

post-1-0-91344400-1434132336_thumb.jpg

 

The barrel arbor was quite rusty so I decided to burnish it - easiest way is to use the lathe...

 

post-1-0-42926500-1434132337_thumb.jpg

 

post-1-0-95745000-1434132337_thumb.jpg

 

post-1-0-44480800-1434132338_thumb.jpg

 

And it came out quite well...

 

post-1-0-80187300-1434132702_thumb.jpg

 

Just need to clean up the rest of the parts and clean the watch now.

 

To be continued.

 

 

  • Like 8
Link to comment
Share on other sites

Great write-up Mark :)

 

I think I've mentioned this before, but has anyone use EVAPO-RUST?

 

I've seen it used on old TV and Radio restorations, and it's amazing stuff.  It removes the rust; but doesn't affect any of the cadmium plating or even the old paint.

 

Might be worth a look into guys.

 

http://www.evapo-rust.com.au/How%20It%20Works.html

Link to comment
Share on other sites

Very instructive and to the point, Mark. It's value is not only for the service but it has an amazing depth in its educational value which is very much appreciated by us newbies! Please, keep it coming!

 

Cheers,

 

Bob

 

PS. I wish I had a lathe and could work on it half of what you do! :)

Link to comment
Share on other sites

Finishing up now...

 

The parts are clean. Some parts are a bit stained but they are sound.

 

post-1-0-52862700-1434369744_thumb.jpg

 

post-1-0-08135500-1434369745_thumb.jpg

 

post-1-0-62838700-1434369745_thumb.jpg

 

Assembling the train...

 

post-1-0-15405500-1434369746_thumb.jpg

 

post-1-0-73791700-1434369746_thumb.jpg

 

And the mainspring/barrel...

 

post-1-0-56237400-1434369748_thumb.jpg

 

post-1-0-07753900-1434369749_thumb.jpg

 

Assembling the barrel bridge...

 

post-1-0-40224800-1434369750_thumb.jpg

 

And the keyless work...

 

post-1-0-16202500-1434369751_thumb.jpg

post-1-0-72430400-1434369747_thumb.jpg

Link to comment
Share on other sites

post-1-0-47868200-1434369979_thumb.jpg

 

And with the escapement back in, the watch is flying...

 

post-1-0-04453700-1434369980_thumb.jpg

 

So now the watch is running fine, the keyless work is smooth like silk. Now ready to case up...

 

post-1-0-43184500-1434369980_thumb.jpg

 

post-1-0-51411000-1434369981_thumb.jpg

 

It's a lovely watch...

 

post-1-0-97824800-1434369981_thumb.jpg

 

:)

  • Like 6
Link to comment
Share on other sites

Cool Mark, I have an old Benrus with the same affliction!  Was about to ask Geo to use his Bergeon Basher but thankfully I had to step away from the watches for a few months.....    This was the first post I read since sitting back at the bench-  Thank you

 

 

Dan

Link to comment
Share on other sites



×
×
  • Create New...