Jump to content

Haych

Haych

By Haych
in Introduce Yourself Here

 Share

Recommended Posts

Haych New Member

Haych

Posted
Posted

Hi guys. Just a newbie here - never really had an interest in watches before but was going to clean & calibrate one of my old watches (one of the dials, small timewatch one, the hand doesn't land back onto zero position it lands slightly at 1oclock angle) but Realised the calibration will be tricky as have zero knowledge about parts and components and only have basic watch kit. It's an Armani exchange ax1214 watch.

 

Stumbled across this because as I was putting it back together I was having trouble with one of the screws which wouldnt seem to go in and screw it self... Its the screw for the electronic board in the watch - to the right of the coil cylinder placed in the middle of the watch. (Crown is facing me)

Anyone have an idea what I am talking about and whats happening?

Link to comment
Share on other sites
Haych New Member

Haych

Posted
  • Author
Posted

Hi I have half opened my watch to calibrate it and realised it's not a good idea because don't have the right tools plus can freely see the parts. ( First time opening a watch)

 

My question is that I am trying to close it back up but one screw for some reason doesn't seem to be going in and screwing... Its an Armani ax1214 watch.

Anyone know why this is happening? I have circled the only area that is giving me this problem and preventing me from closing the watch.

IMG_20210309_222945__01.jpg

Link to comment
Share on other sites
Haych New Member

Haych

Posted
  • Author
Posted
4 minutes ago, Haych said:

Hi I have half opened my watch to calibrate it and realised it's not a good idea because don't have the right tools plus can freely see the parts. ( First time opening a watch)

 

My question is that I am trying to close it back up but one screw for some reason doesn't seem to be going in and screwing... Its an Armani ax1214 watch.

Anyone know why this is happening? I have circled the only area that is giving me this problem and preventing me from closing the watch.

IMG_20210309_222945__01.jpg

I have ensured its the right screw I'm using and the part of pushed down properly etc

Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
Posted

Try removing the board and coil and using the same screw, screw it into the hole and observe what is happening. Is the thread of the hole stripped? Are you screwing into plastic or a brass insert? 

And check all the other screws you have taken out. Are all of them the same? Sometimes we think we didn't mix up the screws, but your bench gremlin will switch them around when you are not looking. 

  • Like 1
Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

These watches are made by Fossil in southern china for Armani and as such there appears to be no technical information available regarding diagrams etc. So other than checking the various screws you removed for length and position, why it doesnt screw in. parts not seated correctly, wrong screw (too short) stripped thread, It is a process of elimination.

  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
59 minutes ago, clockboy said:

Most quartz movements no longer need a calibration. Not sure why the screw is not fitting is it the correct screw.

By "calibration" the OP meant fixing the reset position of the chrono hand. He mentioned that in another post which I have now merged. He did not explain or picture by how much the hand is off, as the reset is normally done with a combination of pressed buttons as mentioned above. He then proceeded to remove screws from the module in the attempt to reach to the dial side, that is of of course never needed, even more on a front loader as this one appears to be.
Correct he was instead in saying that attacking a watch without tools and knowledge is a bad idea. 

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • RichardHarris123
      Hello from Wales, UK.

      By RichardHarris123 · Posted

      At some stage you will have to jump in and have a go. 
    • Neverenoughwatches
      Hello from Wales, UK.

      By Neverenoughwatches · Posted

      Ah so its you thats buying up all the DD calibres 🤨.
    • B1N9S
      Hello from Wales, UK.

      By B1N9S · Posted

      Hi Richard,  I keep buying CAL.59 movements to practice on 🙂 Not started yet though, I'm gathering tools and building my confidence to start.
    • AndrewSi
      No main barrel endshake on Waltham model 1900

      By AndrewSi · Posted

      Problem solved. For some bizarre reason, the hook on the wall of this barrel is not properly centered vertically, but is oddly high on the wall, maybe 3/4 up the way up. When replacing the mainspring, this caused the outer coil to be displaced upwards as well such that it protrudes out of the barrel and caused the barrel lid to not sit quite flush to the barrel. Since this is a motor barrel, the lid is actually the first wheel and inner coil tube/hook all in one piece, with no “snap down” action that would have made the problem more immediately obvious. Maybe with an older mainspring the spring’s end hole was enlarged such that this wasn’t an issue, but hard to say how it ever worked otherwise. Replacing the barrel with one from a different model 1900 where the hook was properly vertically centered allowed the lid to sit flush without mainspring interference and the friction problem went away. The bridge was far too thick to be bent (and isn’t), for those of you thinking that was the problem. Placing the removable arbor in the watch without the rest of the barrel proved that the proper end shake was actually there as long as the overall height of the assembled barrel was correct.
    • Jon
      Mainspring winder question.

      By Jon · Posted

      You are so true on a lot of what you have said. The main reason for changing the mainspring even if the old one is in good order is because it will take out your thinking that the mainspring is contributing to poor power output or fluctuations in amplitude. If a new spring is fitted that box can be crossed off as a potential source of a problem. Most customers are happy to pay the extra £20 for a new mainspring if they are already parting with a couple of hundred pounds for a service. A new spring is an investment for good running for the future.
×
×
  • Create New...