Jump to content

Atomic clock vs my computer


Recommended Posts

Since I just got a circa an early 1990s Longines VHP I've started tracking it to the image of a clock on the NIST Atomic clock site.  I was shocked to see my watch had lost and gained few seconds over 5 days. So today I compared it again and it was -2.74 s. Then I looked more closely at the NIST numerical clock and  image of the clock below it.  They were different, and the clock image was -2.74 and stated "your device's clock is off by 2.74 s". I never imagined the clock image was representing my varying computer clock. Bottom line it it was a relief to learn my watch is right on time and my computer clock varies. Thought I would post this in case others are looking at NIST clock like I did.

\

Henryr

Link to comment
Share on other sites

I often wonder just how precise time needs to be,I have around 80 watches, and thirty clocks and can say that the old adage is very true if you own a clock you know the time if you own more than one you are never quite sure :fpc:

  • Like 2
Link to comment
Share on other sites

Inaccurate time on PC is due to poor OS implementation which uses a single time server, often also inexact like time.windows.com. Below an article on how to change this setting to a better one, like e.g. uk.pool.ntp.org if you're in the UK, or replace uk with your country code. Doing that I have about 0.3 sec difference with the NIST web page, and that is very normal because of the delay between said USA server and a PC in e.g. Europe.

https://answers.microsoft.com/en-us/windows/forum/windows_10-other_settings/how-to-force-windows-10-time-to-synch-with-a-time/20f3b546-af38-42fb-a2d0-d4df13cc8f43

Edited by jdm
Link to comment
Share on other sites

This is very evident when trying to purchase from eBay. You're down to the last few seconds and you place a bid at the last 2 seconds and 5 others bid and you miss out. Turns out there were a couple extra seconds because your computer time and the time on the eBay servers was different. Annoying!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • As is tradition, one step forward, two steps back. Got the board populated and soldered into place without any issues.   But no hum. So I started testing the coils with an ohmmeter. I got 5.84k ohms across D1 (from red to red in the picture below), which is as expected. But I'm getting an open circuit for the other drive coil and feedback coil, D2 and F1 (from green to each of the two yellows).   Since the movement was working with my breadboard setup, it implies I somehow broke the connection between the coils and the solder lugs. They're all the way at the bottom of the lugs, but maybe the heat migrated down and broke the connections? I guess it's possible it happened while cleaning the flux off, but I used a soft artist's brush and isopropyl alcohol. I did a lot of high magnification examination, and I don't see any issues, but let me know if you see anything I missed or if you can think of anything else I should check.
    • 1947 NOS Ambassador 'C'. Actually, the case came without the movement so the movement isn't NOS, but she sure is pretty.
    • Hi attached is the AS 20XX. Service sheet although there is no 2063 mentioned it may be of some use to you AS_AS 2060,1,2,6,4,6.pdf
    • one of the problems we have is visible versus invisible. For instance millennium disulfide another high pressure lubricant black in color. I was told by somebody worked for the Boeing company that they had a piston like device somewhere that has eight call it around it to grab it so it has to slide and in the collet has to grab. But if somebody puts that type of dry grease on where grease with that in it it embeds itself basically in the metal and they have to throw the whole part away they get use it all. So I suspect on all the dry powdery lubricants that they will go into all the basically microscopic cracks and crannies of the metaland that's where it is visually at least until you scrub it off your visually going to see it which is good because you want your lubrication the stay word is. But I'm sure it doesn't last forever on the metal it's just a really nice lubrication  
    • Thanks for the info. I can't seem to find tech sheets for those either.  I'll muddle my way though 🙂
×
×
  • Create New...