Jump to content

It's the little things in life


Recommended Posts

My wife has had a jumbo size jar of pickles of the bench for the last 2 months that has defied all efforts to open it.

Bought a new Silicone jar opener, made no difference.

Holding the jar at 45 degrees and slapping the bottom of the jar to use the 'water hammer' effect didn't work.

Me holding the jar and my son trying to open it didn't work.

Heating the jar lid with me holding the jar and my son trying to open it didn't work.

After coming home tonight from the pub I could see my wife had tried to open it again without success.

I gave up and searched the web for how to open stuck pickle jars and one suggestion was use a bottle opener on the side of the lid.

I very carefully used my best bottle opener (Hand forged by a blacksmith) on the edge of the lid and 'pop' went the lid without the lid being damaged.

The jar is now open after 2 months of trying, is there anything the web can't help you with?

 

:D

  • Like 2
Link to comment
Share on other sites

 Air needs to get in, since the jar has to a good extent been vaccumed, it is heated and the sealer lid is preesed on, as it cools a relative vaccum inside creates suction if you will, that is like strong  pressure from the outside pressing on the lid.

Proper proceesing is of high significance, on jar, bottling and canning lines alike, since in addition to the processed content, the consumer health and producers repution is on the line, processed food safety is No one concern in modern societies of today. 

Other techniques in industry is to preesurize the inside with like nitrogen gas, inerst to the food stuff. Which is probably used in your coke and beer bottles, depending on the country and regulations. 

You can also tap on the rim of the lid, to disfigure the lid enough for air to get in.

Best

Edited by Nucejoe
Not from internet, imported bottling line for son in law, kronas of Germany.
Link to comment
Share on other sites

The best solutions are normally found after a visit to the pub.

I've watched enough episodes of Morse to know that there's not a problem known to man that a beer can't help to solve.[emoji3]

Sent from my moto g(6) play using Tapatalk

  • Haha 1
Link to comment
Share on other sites

Seafoam!  In the tank and the aerosol can into the fuel rail.  (If you can get Seafoam where you are).  Also freed the stuck valve on my '93 Pathfinder and their Deep Creep penetrating oil is the only thing I use on anything from tractors to rusted motion works!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Latest project was a non-running ebay purchase with an FHF70 movement. I stripped and cleaned it, reassembled it, and got it running. So far so good, nothing damaged AFAIK.  I was oiling the top jewel on the balance (the one in the cock) which was a slightly unusual shock setting. I removed the spring (3 leaves) which was part of a chaton holding the cap jewel. This left the hole jewel behind which I retrieved with rodico and then lost it. I was taking it off the rodico, very gently as I thought, with tweezers, and then it just disappeared.  Fast forward a week, I got a donor movement, non-running, with the plan to just take the shock jewel that I’d lost. It was the same movement but had standard incabloc settings, and was steel rather than copper/brass.  I changed the cock and balance complete and it ran, not very well. I switched the lower jewel setting, cleaned and oiled both jewels and the replacement balance. Without the pallet fork the balance swings very nicely with a puff of air. With the fork in place, balance out, it flicks side to side nicely with power in the mainspring.  Put them together and it doesn’t run. The impulse jewel sits in the fork and it stops.      Any suggestions how I proceed? In case you didn’t follow that I have 2 FHF70 movements, nothing broken as far as I can tell, but mixing up the balance wheels and jewel settings results in a non runner. 
    • Oh and this almost perfect third wheel pivot and slightly set mainspring  Ah ok yes i see what you mean, good idea. I'll try that if i fluff this one up. The image isn't great quality but i like the idea though.
    • Why cut the paper, cut a square around the image and grind to it. 
    • I did try that last time Rich , i traced the image from the Bestfit book which is the actual size. But its more difficut to cut the shape from paper than it is to grind the steel to shape. This way is pretty easy and the final shaping is done when fitting the part. There are a couple of things i will do differently next time, clamping the 2 pieces together with a drill press will help to hold while scribing the shape in. This was a bit tricky having only one hole, if using the pins and cork the drill size needs to match the pin diameter so there is no movement at all from the template. This movement hasn't finished frying me yet, damaged thread in the plate crown wheel hole and two rubbed in cracked jewels, thats gonna be much more fun.
    • 👍 Whats not to follow OH ?  You're every inch a pro and a true gent, i always enjoy reading your answers even some of the clock stuff that i dont have a clue about. 
×
×
  • Create New...