Jump to content

Just venting, got a dud Ollie Baker Mainspring winder

Tmuir
 Share

Recommended Posts

Tmuir Distinguished Member

Tmuir

Posted
Posted

I'm just venting a bit, after nearly a year of thinking about buying one I finally ordered an Ollie Baker Clock Mainspring winder from the USA to be shipped to me in Australia.

I received it a few weeks ago, but due to me spraining my wrist I only went to use it for the first time this week.

After mounting it to a board and going to use it I discovered it has several manufacturing defects.

1) The 'tailstock' is several millimeters higher than the headstock, so it holds the mainsprings at an angles.

2)The headstock has been machined off center ever so slightly so it wobbles up and down when turned, this wouldn't be a huge issue if the tailstock wasn't already several mms higher.

3) The pin that holds the click up to stop the winder from turning backwards has not been finished off properly leaving a sharp edge on it which catches and stops you from flicking it over to change the direction when it is under load, although this is only a minor problem that I can easily fix

4) I would not even complain about this if I didn't have the other problems, but the winding handle is just screwed to the arm by an allen screw, which of course unwinds itself when you turn the handle, again this is something I can easily fix, but shouldn't have to.

 

I've contacted the seller who has been around for a while and hopefully they will help resolve the problem, but just annoyed I've waited all this time and got a dud.

I can resolve issue 3 and 4 if the seller can resolve atleast issue 1. Of course the big question is it the headstock, or the tailstock that was manufactuered to the incorrect height...

If they don't want to come to the party I purchased via paypal so will take it to them and they will resolve it, but would rather go first directly to the seller and hope we can resolve it between ourselves

  • Sad 1
Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted
34 minutes ago, Tmuir said:

I'm just venting a bit, after nearly a year of thinking about buying one I finally ordered an Ollie Baker Clock Mainspring winder from the USA to be shipped to me in Australia.

I received it a few weeks ago, but due to me spraining my wrist I only went to use it for the first time this week.

After mounting it to a board and going to use it I discovered it has several manufacturing defects.

1) The 'tailstock' is several millimeters higher than the headstock, so it holds the mainsprings at an angles.

2)The headstock has been machined off center ever so slightly so it wobbles up and down when turned, this wouldn't be a huge issue if the tailstock wasn't already several mms higher.

3) The pin that holds the click up to stop the winder from turning backwards has not been finished off properly leaving a sharp edge on it which catches and stops you from flicking it over to change the direction when it is under load, although this is only a minor problem that I can easily fix

4) I would not even complain about this if I didn't have the other problems, but the winding handle is just screwed to the arm by an allen screw, which of course unwinds itself when you turn the handle, again this is something I can easily fix, but shouldn't have to.

 

I've contacted the seller who has been around for a while and hopefully they will help resolve the problem, but just annoyed I've waited all this time and got a dud.

I can resolve issue 3 and 4 if the seller can resolve atleast issue 1. Of course the big question is it the headstock, or the tailstock that was manufactuered to the incorrect height...

If they don't want to come to the party I purchased via paypal so will take it to them and they will resolve it, but would rather go first directly to the seller and hope we can resolve it between ourselves

I have had a Ollie for several years and have no problems what so ever. Are you sure it is a genuine Ollie. The Ollie baker is well made and solid.

Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
  • Author
Posted

Its an Ollie Baker 'style' mainspring winder, it does have the companies name engraved onto it that made it, but wont post it yet as I may of just got a 'Friday Afternoon' apprentice piece and as long as its sorted I will be happy with that.

The parts are solid enough, its just someone miss measured on one part and were a bit slack on the finish of another part.

Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
  • Author
Posted

Just to keep everyone updated I have been in touch with where I purchased the widner from and provided photos and measurements and they have been in touch with the manufacturer and they are going to machine me up replacement head and tailstocks for the winder, so hopefully in a couple of weeks it will all be resolved.

Link to comment
Share on other sites
  • 1 month later...
Tmuir Distinguished Member

Tmuir

Posted
  • Author
Posted

Just to follow up I received replacement parts during this week and just reassembled my mainspring winder today and it all looks good, so problem is now solved.

Yes this was made by the main supplier of these in the USA, I know of 4 other people with the same brand of mainspring winder and theirs had no issues, I must of just got unlucky, but the manufacturer just going by my photos agreed their was an issue and made me the new parts and sent them to me at their expense so I am happy.

Now I can finally reassemble the clock barrels I am working on.

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • JohnR725
      Seiko 6601 Tech Sheet?

      By JohnR725 · Posted

      yes I noticed the new site and I miss the old site. It's the unfortunate problem of the Internet here today gone tomorrow sometimes some of the stuff gets backed up and sometimes well it does not then the problem with the early Seiko's were there were not necessarily designed for distribution across the planet and as such there is no customer support for them. So trying to find early stuff like technical information or sometimes even parts list for older Seiko is is problematic. But I did find you a you tube video. A quick look he seems to take a heck of a lot of time to actually get to the service single I did not watch all that but it does look like he did disassemble or started to say there's a tiny bit here  
    • HorologyHead
      An intro…

      By HorologyHead · Posted

      RichardHarris123: Hello and welcome from Leeds, England.  I have family all over Australia, went as £10 poms Thanks Richard. Hope you’re able to visit your family here and that they’ve all done well 🙂 My relatives arrived from England in the 1790s transported on the ‘Second & Third Fleets’—a story of timber sailing ships, of convicts and doing well in this huge Country of Australia. When I visited the UK in the 1980s, I was too young to comprehend the depth and breadth of its history…  Best wishes, Mike William Chapman, my 4th great Grandad’s charges, at age 23 read at the Old Bailey; sentenced to 7 years of transportation to Sydney.
    • Endeavor
      New balance staff not riveting to balance

      By Endeavor · Posted

      The whole process and the progress are closely observed, it's hand-driven and very controlled. I can't see the "danger", unless you are watching the TV while doing it. As you could have read, and in this quote "wheel" is the balance-wheel.
    • Mercurial
      AS2063 - hand setting

      By Mercurial · Posted

      Have you got the pallet fork installed in the movement when you see the train move when using the setting works? As nevenbekriev said, without the pallet fork to lock the train, the behaviour you are describing is normal. If this is happening with the pallet fork installed, you have a problem in the gear train, it should be immobile when the pallet fork is locking the escape wheel.  The fit of the circlip above the pinions on that wheel is crooked in your pictures, it should sit flat up against the upper pinion as in Marc’s picture.  Hope that helps, Mark
    • Khan
      Stem broken - can it be rescued?

      By Khan · Posted

      Hi I got a Jaeger LeCoultre K911 movement, where one of the stems was broken. Part no. Should be 401.  Im based in Europe and tried Cousins but its discontinued. They except to get stem in stock for cal. K916 but will that work? Or Is there a way out to join the ends?
×
×
  • Create New...