Jump to content

Recommended Posts

Posted

hi, 

A friend dropped off his foreign Brietling, said had broken the stem.

appears to be a standard setup with subdials at 12:00/9:00/6:00

i have been trying to identify the movement, but i am struggling after the usual Cousins & internet search, in order to get a stem and crown etc.

I removed the dial to help with identification and in doing so broke the 12:00 hour recorder subdial spindle.

Any thoughts on swapping the movement, or general advice would be most helpful....

many thanks

IMG_1569.JPG

IMG_1570.JPG

IMG_1571.JPG

IMG_1632.JPG

IMG_1635.JPG

Posted
16 minutes ago, Yorkie said:

A friend dropped off his foreign Brietling, said had broken the stem.

I don't get the point of using an unusual euphemism, as there is no censorship here. Call it for what it is, a fake.
An original stem may possibly work, but I don't really know.

Posted
1 minute ago, Chopin said:

Have you looked under the balance wheel ? Could it be some sort of Baumgartner ?

LoL, it's a low grade Asian 7750.

Posted

hi JDM , i am learning and a good point on the euphemsim thanks.

guess first i try some chinese 7750 stems, then try to find a 12:00 subdial recorder wheel and replace that.

if not, then i try to replace the movement, but I checked cousinsuk movements but could not find a similar 26mm x 6.25mm movement.

 

hi Chopin, will check and confirm anyways.

 

thanks

Posted (edited)
1 hour ago, Yorkie said:

guess first i try some chinese 7750 stems, then try to find a 12:00 subdial recorder wheel and replace that.

if not, then i try to replace the movement, but I checked cousinsuk movements but could not find a similar 26mm x 6.25mm movement.

I stand corrected, not an A7750, but some other sort of contraption with month / moon / 24hr.
From Cousins it's an DG3836IB, although the same money would buy a lot more Chinese quality and honesty on AliExpress.

Edited by jdm
Posted

Hello Yorkie,

Disregard the watch (or semantics) snobs and use whatever words you choose to describe the movement. Getting to your problem: Check O. frei as the have a large selection of chinese movements. I am sure Cousins UK does too.

It looks like it may be one of these:

59be7247c7bde_ScreenShot2017-09-17at8_59_22AM.thumb.png.5672d2711affc7671f93fd7e8ed8dae7.png

 

Posted
Just now, noirrac1j said:

Disregard the watch (or semantics) snobs and use whatever words you choose to describe the movement. Getting to your problem: Check O. frei as the have a large selection of chinese movements. I am sure Cousins UK does too.

It looks like it may be one of these:

59be7247c7bde_ScreenShot2017-09-17at8_59_22AM.thumb.png.5672d2711affc7671f93fd7e8ed8dae7.png

 

No snobism here, just calling calling things their name. I'm sure that is something you appreciate too.

The mov.t in question is not a small seconds one; I've indicated model and availability above.

Posted (edited)

Fake of course. The movement is based on the DG2813 which is based on the Myiota 8xxx something. 

Nice accurate movement if properly serviced and adjusted that can be found in most low-mid grade replica watches. 

Not a chronograph for sure :D

Edited by szbalogh
  • Like 1
Posted

hi jdm, thanks for the clarification, i ordered replacement today.

Hi Noirrac1j, no worries with snobism, and thanks for the help.

this forum is superb.

Posted

I'm glad you've got it sorted out. I am a collector and have high-end and low-end watches, and don't own any replica watches, but I defend anyone's decision to do so. Besides, you asked for repair help, not input on whether it's  real or not!

Looking forward to your future posts.

Regards,

J

Posted
13 hours ago, noirrac1j said:

I'm glad you've got it sorted out. I am a collector and have high-end and low-end watches, and don't own any replica watches, but I defend anyone's decision to do so. Besides, you asked for repair help, not input on whether it's  real or not!

And help was given. In the end, you're still quibbling about nothing, when the OP has already extended his thanks to everybody. Time to move on, right?

  • Like 1
Posted
3 hours ago, jdm said:

And help was given. In the end, you're still quibbling about nothing, when the OP has already extended his thanks to everybody. Time to move on, right?

Nobody is bringing this up except you @jdm. Yorkie already expressed his thanks to me , and you need to own your remark.  So what's you beef now?

J

 

Posted
On 9/19/2017 at 5:15 PM, noirrac1j said:

Nobody is bringing this up except you @jdm. Yorkie already expressed his thanks to me , and you need to own your remark.  So what's you beef now?

That you started calling others snobist, and continued saying that judgment was given instead of help. And here I'm owning my remark again:

From Cousins it's an DG3836IB, although the same money would buy a lot more Chinese quality and honesty on AliExpress.

Now please, would you drop it and move on.

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Yes, what I wanted to say is that the cock is part of the main plate, manufactured together with it and not meant to be interchangeable. Even if the other cock gets in place, it is not sure that the balance then will stay upright. You should use the original cock when it exists and is not destroyed. The adjustment needed by bending it is not irreversible. It is minimal deforming that is needed. No tools are needed. I have pointed to all needed references here for the balance staff endshake checking and correctness confirmation. The only tool needed for the correction is You thumb. The cock must be fixed on the main plate, no need of special plate with holes and so on. If You will feel more confident, then measure with Vernier caliper the height of the top of the cock where the stones are against the main plate bottom when the shim is fitted and try to reach the same height when bending the cock (with no balance in place!!!) Caliper with screw for fixing is perfect.    
    • Thanks for the reply. I polished the head of the screw using 1500 to 10000 lapping paper and a screw polisher. This is why I think the head blued and the rest of the screw didn't. Silly question, how do you polish the whole screw inc threads, if that's what it needs to blue? 100% clean, Elna red and heated ultrasonic bath + IPA rinse. Finally, there is definitely heat leak as there's about a 30c difference between the brass bed and the soldering station temp. Having said that, the bed temp was stable. I will try to search out a better brass pot, but I haven't found one yet, hence the stainless steel bowl. 
    • Agreed but that's where WD40 excels, water displacement. 
    • I would change the container to a thick walled brass one to start with. Looking at you screw pictures they don’t look shiny enough, really it’s best to do a black polish on them before trying. Also make sure once polished they are scrupulously clean, I dunk my experiments in acetone before bluing.   i think the thin walled stainless container to leach away the heat from the shavings, most successful bluing videos for example use thick walled brass to hold a good deep amount of shavings which acts as a better holder of heat.   Tom
    • …I guess my friend’s dad was duped…and by a Rolex dealer… …well, it’s a good fake 🤪 even the box and papers look legit…  
×
×
  • Create New...