Jump to content

Balance only running when dial facing up

Rich9
 Share

Recommended Posts

Rich9 New Member

Rich9

Posted
Posted

Hi all,

I have been working on a Timor Cal 6060 (Dirty Dozen) which was previously a non-runner, having replaced the mainspring and cleaned all components, I believe I have found the (second) fault!

When facing up, the balance wheel will stop abruptly after a few seconds, but run continually when facing down (dial side up), any thoughts would be appreciated, my initial thoughts was the balance wheel making contact with the pallet bridge but seems odd...

Image attached for reference.

Cheers,

Rich

431889399_1499974533932618_2070071982463402703_n.jpg

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi usually that sort of problem is associated with the balance pivots being worn or Broken or the balance jewels being cracked or chipped, maladjusted balance spring catching the cock or fourth wheel. These are the basics there are other reasons but as you have to start somewhere start with the most common reasons then work outwards.

Link to comment
Share on other sites
nevenbekriev WRT Addict

nevenbekriev

Posted
Posted (edited)

The pivots look OK. In this position, balance may rub on the pallet bridge, the roller table may rubb on the pallet fork, the bottom of roller table may rubb on the main plate, and on the tip of the screw that fixes the bottom endstone plate, the impulse jewel may rubb on guard pin, the rounded part of the pivot may rubb on the hole jewe too. Thiss all may be due to broken, missing or moved down endstone, or the plate with the stone has some dirt or other obsticle under it. But, sometimes different odd reasons can exist, like for example someone has changed the balance from a donnor movement. All the reasons are visible and must be checked. For beginning, remove the lever and it's bridge and do the free oscillations test.

Edited by nevenbekriev
  • Like 3
Link to comment
Share on other sites
  • 3 weeks later...
Mercurial Member

Mercurial

Posted
Posted

One more thing I’d add to the excellent list by nevenbekriev, check that you haven’t accidentally switched the top and bottom endstones of the balance wheel. 

The endstones are sometimes of different thicknesses, and switching them can cause end shake problems that can result in a watch that won’t run dial down. 

Hope that helps,

Mark

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • mikepilk
      Epilame / Fixodrop

      By mikepilk · Posted

      As I'm only cleaning watches in small numbers at home, I pre-clean any significant deposits of old grease and oil before using the cleaning solutions. I scrape off deposits with pegwood and Rodico, and if really dirty, wash parts in naphtha with a brush.  So I'm happy using DX, but can understand why it's avoided by the pros.
    • Neverenoughwatches
      Any tips to correct a sloppy error?

      By Neverenoughwatches · Posted

      I think attaching a nut to the lid to pull it off is the least destructive, any damage damage on the outside is going to an easier fix than any created when trying to push it out from the inside. Scratching up the inside of the lid , mainspring or arbor bearing will be risk. Just my opinion.
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      yes the things we read in the universe I did see some where it was either difficult to clean off or it contaminated the cleaning fluid there was some issue with cleaning. I was trying to remember something about grease where as opposed to a substance of a specific consistency they were suggesting it had a base oil with something to thicken it. That conceivably could indicate that the two could separate and that would be an issue. But there is something else going on here that I had remembered so I have a link below and the description of the 9501 notice the word that I highlighted? Notice that word appears quite a bit on this particular page like 9415 has that property all so they 8200 mainspring grease and that definitely has to be mixed up when you go to use it because it definitely separates. just in case you didn't remember that nifty word there is a Wikipedia entry. https://en.wikipedia.org/wiki/Thixotropy   https://www.moebius-lubricants.ch/en/products/greases I wonder if what you're seeing is the boron nitride left behind after cleaning. In other words it's the high-pressure part of the grease and it's probably embedding itself into the metal which is why it doesn't clean off and shouldn't be a problem?
    • VWatchie
      Epilame / Fixodrop

      By VWatchie · Posted

      Yes and no. I use Moebius 9501 synthetic grease and it is significantly runnier than the Moebius 9504 synthetic grease (and I assume Molykote DX) that I previously used. I haven't seen 9504 spread and it is in my opinion the best grease money can buy. However, my current method of cleaning doesn't remove it from the parts, so that's why I have decided to use the 9501 instead. I believe I read somewhere that Molykote DX too is difficult to clean off. Thinking about it, I'm pretty sure my 9501 grease which expired in June 2022 is runnier now than it was when it was new, but whether new or old it always needs to be stirred before use. So, that's why I treat the parts of the keyless works, cannon pinion, etc. with epilame. That was very thoughtful of you and something that had completely passed me by. Not sure what the epilame will do when it wears off in a non-oiled hole. Anyone?
    • watchweasol
      Seiko 6601 Tech Sheet?

      By watchweasol · Posted

      Hi not found one either yet,  close relative is the 436 and 4361 according to ranff.db.   It gives quire a lot of detail but not as good as the old site.      RANFF.DB.
×
×
  • Create New...