Jump to content

Bezel Issue

PeterGe
 Share

Recommended Posts

PeterGe WRT Addict

PeterGe

Posted
Posted

Hi Guys,

 

I got a Tag Heuer here with a bezel issue.

The bezel just will not snap onto the case.

There are 2 spring under the bezel, the retention spring & a click spring.

I suspecting the retention ring is causing the issue, together with the rim on the case itself which seems to have some damage from previous attemps.

(I'll try to upload some images to make it more visual)

 

Anyone who has encountered similar issues? Any advice/tips are appreciated!

 

 

 

 

 

Link to comment
Share on other sites
WillFly Distinguished Member

WillFly

Posted
Posted

I've encountered a snap-on case cover which just wouldn't snap back on, no matter how much I used a case press. In the end, I sandwiched the case and cover between two of the plastic rings from the case press and slowly eased them together, bit by bit, in a circular motion in a bench vice. They snapped back together eventually with quite a crack.

 

However, the case and cover were in perfect condition - just very tight. If you have a slightly misshapen bezel or rim, it might be worth trying to see if the case rim and the bezel have deviations in them - and if the deviations might sit one on top of the other. Just a thought.

 

And as you say, the movement ring might not be properly seated.

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted (edited)

Take of all springs out and see if the bezel fit the case properly . If it does test one spring at a time . The retension ring maybe needs some tweaking to make the bezel sit properly on the case . It should have 5 or 6 or more bends and they should protrude a little inside the bezel . Like on this Rolex bezel .

 

post-644-0-77701000-1433519246_thumb.jpg

Edited by rogart63
Link to comment
Share on other sites
PeterGe WRT Addict

PeterGe

Posted
  • Author
Posted

Hi Rogart, That's indeed the approach I tried to take. But it just seems that the problem might be both with the retention spring's shape & perhaps also with the slightly distorted rim on the case.

I'll try to make some pictures of it, didn't get to it during the weekend.

 

Does anybody knows whether these retention springs can be purchased somewhere? I searched cousins but couldn't find them.

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted (edited)

Have you looked at cousinsuk ? Under the Tag heuer brand .Watch parts branded ? An search for you specific model . Otherwise their is a company in uk that has .watchpart co.uk 

 

Looked at cousinsuk and they didn't have any . Strange?  But the other has them . 

Edited by rogart63
Link to comment
Share on other sites
PeterGe WRT Addict

PeterGe

Posted
  • Author
Posted

Thanks for all the suggestions. The bezel without the springs fits just fine. The click spring also seems ok. It really seems the retention spring which is causing the issue69c1ef1928e95f64cc1ff53aed4cc168.jpg522db594d4ea95ab97f0fdbd90baa9ee.jpg51e08f6ea20b528d6a526647215853f5.jpg. The shape is not ideal and it has very little tension. Guess a new spring is in order? I've included some pictures

Verzonden vanaf mijn iPhone met Tapatalk

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted

The spring doesn't look to good . It doesn't fit properly in the groove . It could be bent back to shape but the easiest way would be a new spring . The shape of the edge on the watch looks ok to me . A few marks but that would not be a problem . 

Link to comment
Share on other sites
  • 1 month later...
PeterGe WRT Addict

PeterGe

Posted
  • Author
Posted

Bummer.... I ordered a new bezel spring at .watchpart co.uk.

After a long waiting time & inquiries from my side, They cancelled & refunded my order.

They can't provide me with the part.

 

It seems I will have to find an other supplier :-(

 

The search continues.......

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

I had issues with that company regarding a Tag bezel. They wouldn't answer phone calls or letters. I took advice from citizens advice and it took a legal binding letter to get my money back.

Tag parts are notoriously hard to come by, and after much eBay searching I eventually purchased a new bezel from someone in Florida.

That reminds me, I must put that watch back together again!

Link to comment
Share on other sites
anilv Distinguished Member

anilv

Posted
Posted

Hi Peter,

 

Looking at the pic of the bezel (leaning on the pad), the bend in the spring at approx 2 o'clock should be in the slot. As it stands, when you try to install the bezel it just pushes the spring upwards and not outwards.

 

Look at Rogart63's bezel, all the points are in the groove.

 

You need to tweak the spring a bit so that all the points are 1) in the groove and 2) lays flat. Once you get it looking like Rogart63's, then try installing.

 

It should be an easy fix... easier than adjusting a hairspring at least!

 

Anil

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • HorologyHead
      Intro

      By HorologyHead · Posted

      Hi to Blackminou29–am a collector/ caretaker—good luck to you following your repair course—with hindsight I wish I’d pursued a career in both watchmaker/ jeweler fields—good luck with whatever career passion you engage.   Thank you Watchweasol for posting the amazing TZIllustratedGlossary! Best wishes, Mike
    • JohnR725
      Seiko 6601 Tech Sheet?

      By JohnR725 · Posted

      yes I noticed the new site and I miss the old site. It's the unfortunate problem of the Internet here today gone tomorrow sometimes some of the stuff gets backed up and sometimes well it does not then the problem with the early Seiko's were there were not necessarily designed for distribution across the planet and as such there is no customer support for them. So trying to find early stuff like technical information or sometimes even parts list for older Seiko is is problematic. But I did find you a you tube video. A quick look he seems to take a heck of a lot of time to actually get to the service single I did not watch all that but it does look like he did disassemble or started to say there's a tiny bit here  
    • HorologyHead
      An intro…

      By HorologyHead · Posted

      RichardHarris123: Hello and welcome from Leeds, England.  I have family all over Australia, went as £10 poms Thanks Richard. Hope you’re able to visit your family here and that they’ve all done well 🙂 My relatives arrived from England in the 1790s transported on the ‘Second & Third Fleets’—a story of timber sailing ships, of convicts and doing well in this huge Country of Australia. When I visited the UK in the 1980s, I was too young to comprehend the depth and breadth of its history…  Best wishes, Mike William Chapman, my 4th great Grandad’s charges, at age 23 read at the Old Bailey; sentenced to 7 years of transportation to Sydney.
    • Endeavor
      New balance staff not riveting to balance

      By Endeavor · Posted

      The whole process and the progress are closely observed, it's hand-driven and very controlled. I can't see the "danger", unless you are watching the TV while doing it. As you could have read, and in this quote "wheel" is the balance-wheel.
    • Mercurial
      AS2063 - hand setting

      By Mercurial · Posted

      Have you got the pallet fork installed in the movement when you see the train move when using the setting works? As nevenbekriev said, without the pallet fork to lock the train, the behaviour you are describing is normal. If this is happening with the pallet fork installed, you have a problem in the gear train, it should be immobile when the pallet fork is locking the escape wheel.  The fit of the circlip above the pinions on that wheel is crooked in your pictures, it should sit flat up against the upper pinion as in Marc’s picture.  Hope that helps, Mark
×
×
  • Create New...