Jump to content

Can you spot why this is a marriage

oldhippy

By oldhippy
in All Things Clocks

 Share

Recommended Posts

RogerH WRT Addict

RogerH

Posted
Posted

At they are selling it as sold as seen and not a genuine article. As Bod said, it would be good to see inside but the fact nothing seems to fit clearly shows it's not right. The dial is quite impressive - I didn't know you could do that!

Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
Posted

I'm not even sure if the chapter ring goes with that dial, look at the nasty way it has been riveted on with steel rivets at 12,3,6, and 9. I have trouble believing that the original maker would fit it so clumsily.

It's hard to tell from the photo but the dial also looks like it has gaps below and to the left so it does not fit the hood.

I'm also guessing those hinges are not original either.

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

The case and style of the clock looks ok its made of oak, the dial also looks original apart from the re work and fitted blanks (badly) which would mean a movement change. Normal Wm Hargreaves 1741 to 1813.  clocks go for around £800 to £1000 plus as this is offered at £250  and the fact there are no movement pictures  bascially its a Bitsa (marriage) Settle is in North Yorkshire near Skipton, My home county.

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Many longcase clocks had the bottom either cut off or added due to the fact most of them stood on stone floors and were subject to a great deal of damp as the floors were scrubbed and swilled off with water with little regard to the clocks that stood on them. only on the big houses did they stand on oak or pine floors and did not suffer as much. 

  • Like 1
Link to comment
Share on other sites
KarlvonKoln Distinguished Member

KarlvonKoln

Posted
Posted

The taper pin on the center arbor is the only way I know there isn't a quartz movement hiding in there.  Outside of that, not specializing in this kind of clock, seeing mismatching with appearance and fit and finish would make me wary enough to stay clear of it, unless I became determined to restore it.

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
  • Author
Posted
15 minutes ago, KarlvonKoln said:

The taper pin on the center arbor is the only way I know there isn't a quartz movement hiding in there.  Outside of that, not specializing in this kind of clock, seeing mismatching with appearance and fit and finish would make me wary enough to stay clear of it, unless I became determined to restore it.

A waste of money restoring this. It would be throwing good after bad. 

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Questions about my Bravingtons Renown Mantel Clock

      By Neverenoughwatches · Posted

      Hmmm you know when i said some damp might have caused the bubble originally hmmm 🤨
    • Neverenoughwatches
      404 Club Reboot

      By Neverenoughwatches · Posted

      Are you all jerking my chain, I'm a yorkshireman £4.04 is too much 😆
    • Kkramme
      Blew it with a coil

      By Kkramme · Posted

      [Myota2034] Custom simple quartz watch — PricewaterhouseCoopers On a very very different note, here is a watch from approximately 2000 when I was a Partner with PwC, Management Consulting. It was a simple “marketing watch” with a clever “vase of knowledge” that is subtly revealed on the dial as the second hand progresses. Clever for a simple watch!⌚️
    • Neverenoughwatches
      Mainspring winder question.

      By Neverenoughwatches · Posted

      I think someone else has though. Some where here using a modified perspex sheet. I may be wrong i may be right , i think it involved fitting the arbor to a pin vice. I dont have experience of the bergeon winders, are the handles not interchangeable ?
    • Neverenoughwatches
      Dial Dots

      By Neverenoughwatches · Posted

      Never tried dial dots, i always considered them as a bit of a bodge.  You are adding something that was never intended to be there. I wonder how the adhesive reacts to any part of the movement, hot summer heat and i think things might turn sticky. Most adhesive backed stuff has a tendency to soften and slide around so it may spread, i have used a lot of so called sticks all adhesives in my industry that are just not up to the job. I suppose they get you out of a problem quickly, but how permanently might that be ? I would just explain to the owner that it may or may not work. WWs other ideas are a much more permanent solution but both have their risks . I've tried milling and dial feet replacements, hmm it was ok, ive heard of folk dimpling the face , so that needs care . And i have soldered a few times , all with good results but i am very careful and I practiced it a lot.
×
×
  • Create New...