Jump to content

Vostok Komandirskie


Recommended Posts

Screenshot_20210209-001459_eBay.thumb.jpg.2bb1a89df91f01a3ce93ac21400a7b22.jpgI just completed this project yesterday. I got it from ebay as a non runner. It had so many problems that I not sure which one finally did it in.

20210208_120349.thumb.jpg.3e729c9325ad6cd94363bc7193c79b66.jpgThe tail of the mainspring had broken off. I spot welded it back.

The minute hand could move but not the hour hand. I found that the cannon pinion was not pressed all the way in. 

The movement was filthy. There was oil everywhere. And look what I found under the mainspring barrel. 20210206_210046.thumb.jpg.944b89c5b382e3b294c9ebb0ce84fb26.jpg

A Russian spy bug!

The cleaning and oiling was straightforward. But the hairspring was so greasy that I had to rinse it 3 times.

I relumed the dial and I am quite pleased with the outcome. 

20210209_205438.thumb.jpg.8ad27fafedfda741823163029ea029d0.jpg20210213_203633.thumb.jpg.a48a99df0c37a9601d8742bfebed13da.jpg

  • Like 4
Link to comment
Share on other sites

  • 4 weeks later...
40 minutes ago, VWatchie said:

That lume looks great! What type is it and where can I get it? Thanks!

I used a lume powder from Aliexpress mixed with Bergeon lume powder. I think the Chinese lume powder glows brighter and lasts longer, but the grains are very coarse. I had to grind it in a mortar and pestle and seive it to get a finer powder.

I mix my lume powder in UV nail polish. I used a light orange luminous nail varnish to give it an "aged" look.

  • Thanks 1
Link to comment
Share on other sites

47 minutes ago, HectorLooi said:

I had to grind it in a mortar and pestle and seive it to get a finer powder.

I would advise a dust mask when grinding it, it is pretty abrasive stuff, so you don't want to be getting too much of it in your lungs. The same applies to pretty much any ceramics. Actually if in doubt, when grinding stuff, any stuff, wear a mask.

  • Like 1
  • Thanks 1
Link to comment
Share on other sites

2 hours ago, HectorLooi said:

I used a lume powder from Aliexpress mixed with Bergeon lume powder. I think the Chinese lume powder glows brighter and lasts longer, but the grains are very coarse. I had to grind it in a mortar and pestle and seive it to get a finer powder.

I mix my lume powder in UV nail polish. I used a light orange luminous nail varnish to give it an "aged" look.

Awesome tip! ?

Any special reason you're using a UV nail polish? I know nothing about it.

Edited by VWatchie
Link to comment
Share on other sites

UV nail polish gives unlimited working time. There is no solvent evaporating away and making the lume paste lumpy. There is no need to hurry. When you are happy with the placement and thickness of the lume, then you cure it under a UV nail lamp. 

  • Thanks 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • The cannon pinion (be it conventional style or what you see in this movement) should slip on its arbour so the hands can be set independently without affecting the gear train.  If there is too much friction between the cannon pinion and the second wheel, turning the hands to set them backwards can sometimes force the escape wheel teeth to overrun the pallet stones, creating the behaviour you describe. The train is running in reverse when this happens.  This can often chip the pallet stones. I’d say at least half of the watches I’ve inspected with very tight cannon pinions had chipped pallet stones. Hopefully this isn’t the case with your watch.  I’m not familiar with this movement but you need to get the friction in the cannon pinion adjusted correctly.  Hope this helps, Mark
    • Pallet fork was in. I’d had the movement running ok, and only removed the balance to flip it over and install the keyless works and date mechanism. The pallet fork wasn’t locking the gear train when hand setting - it was oscillating as the escape wheel rotated. This may have been in one direction only - can’t remember. 
    • Hi   Find attached parts/repair notes for the JLC 911,  might be useful. JLC_JLC 910, 911.pdf JLC_JLC 910, 911 Repair Notes.pdf
    • Hello and welcome to the forum Dan. Used to know Middlesboro quite well, that was twenty years plus ago. Attached a little reading to get you started. TZIllustratedGlossary.pdf
    • for the most part no. Each individual watchmaker and/or shop had their own system. One of the shops I worked at basically had a reference to a page number in a book. then there are some shops that do no markings at all as they keep their records on a computer and they don't have to mark the watch. Usually if somebody is marking and they've service the watch before you'll see those next to each other. then as far as anything resembling a standard goes at one time the American watch and clockmakers Institute assigned all of their members a number. but that was a very long time ago and I doubt that they are using it anymore.
×
×
  • Create New...