Jump to content

Having a hard time getting watch back off

Evergreen64
 Share

Recommended Posts

Evergreen64 New Member

Evergreen64

Posted
Posted

Hello,

I have an 88 Rue Du Rhone chronograph. It's battery is dead and I would like to replace it myself. It has a press on case back which I can't seem to get off. I have tried using a case knife on a small indentation on the side which looks like it was designed for a case knife but it won't budge. I don't want to apply too much pressure because I have had a case knife slip and cut me before. Any ideas on how to go about removing it safely?

Thank you,

Mike

Link to comment
Share on other sites
VWatchie Distinguished Member

VWatchie

Posted
Posted

s-l1600.jpg.332883ac26196f8c8becccf718baa30e.jpg

I got tired getting off bezels and snap-on case backs so I got myself one of these Chinese "Snap Back Watch Case Opener Bezel Remover" on eBay. I've only used it with bezels so far, but it has worked really well reducing the pain and risks to a minimum. I just hate it when I damage myself or my watches. I feel pretty sure it will work just as well with snap-on case backs.

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted (edited)
11 hours ago, VWatchie said:

I just hate it when I damage myself or my watches. I feel pretty sure it will work just as well with snap-on case backs.

Copy of an expensive Horotec, I have pictured few more in the topic below. These are really needed only with some recent Swiss casebacks which are very tight and have no indentation at all. Not an issue with old watches.

Edited by jdm
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
1 hour ago, VWatchie said:

Depends on who’s opening it too :rolleyes: I recommend this tool for any watch; new and old. Especially if you need to remove bezels as well.

Your is in fact mainly a bezel and bracelet (in a different versions that adds the punches) tool. That is because the blades are sturdy but not sharp, something that is more desirable when there is no initial levering point.

Link to comment
Share on other sites
Klassiker Distinguished Member

Klassiker

Posted
Posted

I have the black and green one pictured above, and have used it successfully to lever this off

298414930_Caseback.thumb.JPG.5de29fdf7d8c0e20b5b4b54917843199.JPG

which was impossible with a conventional case knife. It completely removes the risk of slipping, so you can apply much more force in a more controlled way. No marks, on me or the watch. I paid a bit more than 20 Euros for it.

Link to comment
Share on other sites
  • 2 years later...
Waggy Distinguished Member

Waggy

Posted
Posted (edited)
On 6/23/2020 at 1:11 AM, VWatchie said:

 

I got tired getting off bezels and snap-on case backs so I got myself one of these Chinese "Snap Back Watch Case Opener Bezel Remover" on eBay. I've only used it with bezels so far, but it has worked really well reducing the pain and risks to a minimum. I just hate it when I damage myself or my watches. I feel pretty sure it will work just as well with snap-on case backs.

Can anyone tell me what the rod on the right is for on the row of bits. It looks like it should stop the bit from sliding out, but the rod itself keeps dropping out of the hole in the back of the bit.

s-l1600.jpg.332883ac26196f8c8becccf718baa30e.png

I was also given one of these:

10810.thumb.jpg.bd4e9c8d39bb39e01ef000b365a0827c.jpg

Does anyone know the best time to use it? When is it better to use this instead of the other types?

Edited by Waggy
Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
Posted

That rod is for twisting the bit to lever the caseback off. But I wouldn't use it that way as it tends to leave marks.

In fact, I don't use this tool as most people would, i.e. turning the big knob and driving the bit under the caseback. The way I use this is to tighten the knob until it is tight, then use a small hammer and tap gently on the back of the bit. This loosen up the big knob a little and I would repeat until the caseback pops off or the knob doesn't seem to loosen with tapping anymore. If that happens, it means that the bit is too thin and is unable to pop the cover off. This is probably when the skinny rod is used to twist the cover off but I don't do that as it can mar the finish. I would then insert my case knife into the crack that has opened up and wedge it off.

The bits are very hard but brittle. Regular inspection and dressing the tips is necessary. 

Good luck.

  • Thanks 1
Link to comment
Share on other sites
tomh207 Super WRT Addict

tomh207

Posted
Posted
4 hours ago, Waggy said:

 

I was also given one of these:

10810.thumb.jpg.bd4e9c8d39bb39e01ef000b365a0827c.jpg

Does anyone know the best time to use it? When is it better to use this instead of the other types?

I have that one too, I use it when I am struggling with the case knife. Use a sturdy case vice and it pops the caseback off with the spring loaded shock system, much like the action of an automatic centre punch.

 

Tom

  • Like 1
  • Thanks 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      Yes, I was referring to the (jewelled) gear train with HP (most of the time, I use 1300, but when Rolex says 1000, I'll use 1000).
    • JohnR725
      Without Our Forum

      By JohnR725 · Posted

      did I miss the update of the message of something changing?      
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      I suppose it would depend upon what your lubricating with those? for instance what does the manufacturer say about those lubricants? I have a PDF from the manufacture and a rather peculiar statement found on the bottom of the chart. my suspicion is the reason the recommending would be without epilam the HP oils like the spread except when they're in Ruby jewel's with steel pivots. tableEN lubrication 2020.pdf
    • oldhippy
      Is this a 'hack' ?

      By oldhippy · Posted

      These types of hairsprings become weak with age and very fragile. Which I expect it is that giving you trouble, and that wheel is not the correct one, if it were not bent I don't think the movement would run as the teeth are not the correct height. The problem you have is price which depends on you. It can be repaired but is it worth it to you, because there is little value in the clock. A wheel can be made and hairspring replaced. Or hang on to it and keep looking on ebay which is your best bet for replacement parts or even a complete movement but it will be like finding a needle in a haystack. 
    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      I did that also for a few movements - well, mainly in/around the train jewels. I made big efforts to epilame the mainplate WITHOUT getting Epilame into the Pallet fork jewels (where it's not supposed to be, right?). I made litte barriers with Rodico around that jewel and used drops from a syringe to apply on the rest.  However, I've now stopped doing this. For three reasons: 1. It's a hassle and consumes more of this liquid gold. 2. I didn't see the need when using HP1000/HP1300 lubricants and grease for most part. The two places where I'd use 9010 (i.e. escape wheel and balance) receive Epilame in specific places... or the cap-jewel-setting of the balance suspends the oil sufficiently be capillary action (see my "conflict" about using Epilame on the balance jewels).  3. Lastly, and here I really wonder about yours and others' experiences: I felt that applying Epliame to the train jewels left them looking hazy (borderline dirty) compared to the (painstakingly achieved) sparkly clean results of my cleaning process. I just can't help but think that the Epilame residuals would mix with the oil and cause more friction/wear. I don't know.    simple: it'll stay there. It won't move any further. That's exactly what is happening if you epilame a cap stone. You end up placing the 9010 right on top of the epilame and the oil will sit nicely on that spot.
×
×
  • Create New...