Jump to content

Bucket list repair job


Recommended Posts

I'm sure all of us have a watch that we have put off completing the repair. The "One day I'll get to it" watch.

It is usually a watch early in our career/hobby. The one that was beyond our abilities at that time. The one that required a special tool that we didn't have. The one that requires a replacement part that is as rare as "unicorn poo".

Amid the Covid 19 lockdown in so many countries, now is the best time to revisit these projects that we have put off for so long. :D

Link to comment
Share on other sites

I'll start off the 1st one.

This my Waltham 12s pocket watch. Beautiful white gold case. Fully jewelled.

I was a non working watch which I got for a bargain from ebay. I found that the mainspring was broken. I temporarily fixed it by annealing the end of the mainspring, drilling a hole for the catch and shaping it to fit the barrel arbor. It worked fine.

So I proceeded to clean it while I went to order a new mainspring for it. Somehow I got distracted and forgot it was still soaking in my ultrasound. By the time I remembered, the shellac from the pallet stones had disintegrated. :pulling-hair-out:

20200330_103537.jpg

20190930_160231.jpg

20191001_140809.jpg

Link to comment
Share on other sites

I bought and repaired an 1871 Elgin pocket watch only to drop it while doing the final reassembly and broke the balance! I was utterly heart broken! It is still sitting waiting for me to get back to it. When I do, I'll have to source a correct dial and hands and hour gears as I "borrowed" them to complete and even older 1869 Elgin that I still have.

20200330_123642.thumb.jpg.41b60974e210e5fb633a9bafe1153b03.jpg

Link to comment
Share on other sites

I had been waiting for ages to get a  Universal Geneve, and finally got a nice 40s vintage Cal 267.

It just need a little tweek to adjust the hairspring overcoil. I bought some Vetus tweezers with a very fine point - but they were quite hard to compress. I gave the overcoil the required tweek, and released the tweezers too soon ..... completely trashed the hairspring.

Still makes me squirm when I think of it.

Of course, hairsprings for these are like the proverbial "unicorn poo". The balance was only used on one other calibre. 

I have a permanent watch on ebay ..... one day.

20181024_133205.thumb.jpg.cc6b8366f21b03db6ccee045c9bda374.jpg

Link to comment
Share on other sites

I bought some Vetus tweezers a while back and also found them hard to compress so went back to my old cheapies. I also bought to do HS but didn,t risk it fortunately, else I might have been in same boat.  HS not my forte at the best of times !!

Link to comment
Share on other sites

Actually, I have procured all the necessary tools and materials to re-shellac the pallet jewels. Read up and watched many videos on escapements.

Probably the only reason for my procrastination is that after many failed attempts, during my moment of despair I prayed to God that he not let me leave this earth till I finished this job. :startle:

20200330_234930.jpg

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Yep, i pulled that up as well when i was looking,  there is definitely parts out there if you are prepared to go out and find them.  I watched that video years ago, I'm not so sure about probing the coil like that. If you are going to touch the coil use the side of the probe or at least shape a nice round end to it.
    • Hi and welcome to the forum.   As you are already familiar with watches the attachment you may find useful Witschi Training Course.pdf
    • I saw this listing from Australia this morning on Ebay, it might be your only option, good luck.... https://www.ebay.com/itm/145735044565?itmmeta=01HWCRFPEYDDTCXYCRX7ESQH3K&hash=item21ee7c4dd5:g:f2oAAOSwaMhmI5tq&itmprp=enc%3AAQAJAAAA4PzZAWzJj0HOwVM7Xl6qUqGIYly3BvZhzNybkxWf8GJYkKwVh0SpeZ0XYBmoZyjaboPOlJYzdY9svwhQXfR7V%2BiMApTEYFLvJcs8FxTzy1VFCBLR8ADc7V89%2B%2FYvQKdks2KDNNEqAFZN0Hni9zQG078wKL34x0eRK%2Fu843fYdH%2FVIAiOZ5%2BbOmySNdu%2Bv4cSemywC%2FWfaiI%2Fj5D3YWk2PaySdPfu7lUaMadcyhmHZM6l6NllJd1eK%2BdblkJD98pTzVuxRDne5AQaCYawls%2FaoQK9B7epV%2B87TIbD9Ulr4qdC|tkp%3ABk9SR-rnvpjjYw
    • Hi. In the picture not only does it depict that the wheel is bent but also the plate or is that due to th angle of the picture.  Already received very good advise so I will butt out.
    • welcome, sounds like you are on your way so far, you also might be able to help with gold/plated case repair for some .....
×
×
  • Create New...