Introduce Yourself Here
New to the community? We like to know who we are chatting with :)
So why not introduce yourself here first!
4735 topics in this forum
-
- 6 replies
- 1.3k views
-
- 6 replies
- 1.5k views
-
- 4 replies
- 656 views
-
- 3 replies
- 798 views
-
- 4 replies
- 912 views
-
- 3 replies
- 588 views
-
- 6 replies
- 766 views
-
- 1 reply
- 1.1k views
-
- 3 replies
- 614 views
-
- 2 replies
- 564 views
-
- 5 replies
- 608 views
-
- 2 replies
- 1.2k views
-
- 4 replies
- 622 views
-
- 4 replies
- 685 views
-
- 7 replies
- 737 views
-
- 2 replies
- 1.3k views
-
- 2 replies
- 1.3k views
-
- 5 replies
- 2.3k views
-
- 9 replies
- 1k views
-
- 3 replies
- 528 views
-
- 3 replies
- 491 views
-
- 5 replies
- 878 views
-
- 3 replies
- 603 views
-
- 2 replies
- 542 views
-
- 4 replies
- 419 views
.thumb.jpg.cb17a66989f1e796fd4217db2e9ca9df.jpg)
-
Topics
-
-
Posts
-
It might be a good idea to clear out all your browser caches (this should include any DNS caching). I might also be inclined to recommend Roy from the IT crowdās answer to everything - Have you tried turning it off and then on again? šĀ But seriously - sometimes a phone reboot can help. If problem persists then you can then know that its an upstream issue rather than your device. -
By bakeeneitje · Posted
Hi, I'm Marcel (51) from The Netherlands.Ā I recently started my first vintage watch project. Before that I mainly worked on the necessary basic knowledge with the help of videos, forums, such as WatchRepairTalk, and other online information. So today the step to also become active on WRT. I hope to learn a lot from you. Best regards, Marcel -
By watchweasol · Posted
Hello and welcome to the forum, the best path to take is to get some medium priced tools , look at Cousins UK . They are a material house and are open to all. There medium priced screwdrivers are middle of the road and wil if looked fore serve you well into the foture I have added a little reading for you to help.Ā TZIllustratedGlossary.pdf Watch_tools_tipps.pdf -
After another long hiatus (while waiting for truing calipers to arrive), Iāve made some more progress. TRUING IN THE FLAT I was able to use the calipers I purchased to true the wheel in the flat. Thereās still a very slight eccentricity in the round, but Iām going to leave it as is. It doesnāt wobble any more and Iām happy with that. Thanks for the tool recommendation @mbwatch. It worked well, though I must say it takes a delicate touch to get the balance between the calipers. Also, my calipers effectively have four different variations based on the orientation of the arms (2 sides, 2 orientations each). Some are more tapered than others, though to what end, I canāt quite tell. My first thought was that flipping them over yields arms that can be used for poising. They are K&D horizontal calipers, btw. OSCILLATION TEST @nevenbekrievĀ @JohnR725Ā After truing the wheel in the flat, I carefully remounted the hairspring and did your oscillation test. Balance wheel mounted to balance cock, no pallet fork, rotate balance wheel 180 degrees, let it go, and time+count the oscillations. Results as follows for dial down orientation: Duration: 1m 15sec (to full stop) # of oscillations: About 125, though the amplitude of the oscillations decreased significantly, as one might expect I should redo the test in at least two other orientationsā¦Forgot to do that. šĀ In general, itās safe to say this watch has a pretty low amplitude, likely for a variety of reasons. I havenāt oiled the balance jewels FWIWā¦I should probably do that, but I really donāt want to keep disassembling and reassembling the balance. Is it possible to oil those jewels (top and bottom) by just removing the capstones and putting in a tiny amount of oil, with balance in place? I can see how having the pivot in the jewel hole could change how capillary action works, and thus might pull more oil in than desired. However, those capillary forces will be in effect anyway once the balance is inserted. PRACTICE MOVEMENTS @JohnR725Ā I agree with your sentiment about using practice movements wholeheartedly, and Iāve done that to some degree. The watch Iām currently repairing is for a friend, and she was willing to have me treat it as a ālearn-by-doing experience.ā With that said,, I probably should have purchased a few more ābeatersā before getting to something where I donāt want to muck things up. Iāve still got a couple of those on the bench that I used as donors, and Iāll try to rehabilitate them. -
Hi, this is the first place I found when looking for advice so I hope someone could advise me.Ā Im completely new to touching watches but Iāve always wondered how they work.Ā Iāve bought a cheap movement, an ETA replica to take apart and rebuild.Ā Im thinking Iāll need some screwdrivers, tweezers, movement holder and a loop? My goal is just to have a go first and see if I enjoy it enough before buying more tools.Ā Do I buy cheap tools for now and get better quality tools later if I enjoy it like I think I will? or will the cheap tools be a pain and take some of the fun out of it?Ā With quality tools being relatively expensive Iām unsure what to buy.Ā Ā Any advice would be greatly appreciated!
-
