Jump to content

Stubborn Bulova case back

Lc130

By Lc130
in Watch Repairs Help & Advice

 Share

Recommended Posts

noirrac1j Distinguished Member

noirrac1j

Posted
Posted

I've seen your link, but are you sure that's the same watch as yours? First of all,  If the back of your watch comes off, there would be NO ROOM for the dial+movement to come out as it would be a very small opening and obviously the dial would have to be attached to the movement. What does the front of the watch look like? Does it have a small dial and:huh: a large bezel?

J

Link to comment
Share on other sites
Lc130 WRT Addict

Lc130

Posted
  • Author
Posted (edited)

I'm trying to open it on the side opposite the crown.  That's where the chewed up notch is.  I can't tell if that notch is machined or simply hacked in by others trying to open it.  The notch is seen on the second pic. 

Thanks!

Charlie

 

IMG_2766.JPG

IMG_2765.JPG

IMG_2764.JPG

IMG_2763.JPG

Edited by Lc130
Link to comment
Share on other sites
noirrac1j Distinguished Member

noirrac1j

Posted
Posted

I would say it has a two-part stem and you have to remove the crystal to get the movement out through the front. That notch you've been trying was someone's wishful thinking. The stem should pull out completely--use a pair of tweezers or watch hand removers with low to moderate force. You'll need a crystal remover for the next step.

J

Link to comment
Share on other sites
Lc130 WRT Addict

Lc130

Posted
  • Author
Posted

OK, I was able to open a seam in the back using a razor.  The back definitely comes off.  I can just barely get a Horotec case knife in and can see the seam open and close when I rock the blade.  It wont pop off.  Is there some penetrating solution I should try?

Thank you

Charlie

 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
10 hours ago, Lc130 said:

OK, I was able to open a seam in the back using a razor.  The back definitely comes off.  I can just barely get a Horotec case knife in and can see the seam open and close when I rock the blade.  It wont pop off.  Is there some penetrating solution I should try?

Some criminal "repairers" glue the back to make sure the customer comes back to them in desperation. Apply no more than 2 or 3 drops of acetone (nail varnish remover) to the seam. However most likely that's not needed, just go around the seam slowly and patiently with a small blade, max 5mm wide. Don't twist, just pry it up. That will minimize marks on the case. 

Link to comment
Share on other sites
noirrac1j Distinguished Member

noirrac1j

Posted
Posted
1 hour ago, Lc130 said:

OK, I was able to open a seam in the back using a razor.  The back definitely comes off.  I can just barely get a Horotec case knife in and can see the seam open and close when I rock the blade.  It wont pop off.  Is there some penetrating solution I should try?

Thank you

Charlie

 

Wow you found it.... that back must be glued on like @jdm said. If acetone won't work maybe isopropyl alcohol?

Link to comment
Share on other sites
Lc130 WRT Addict

Lc130

Posted
  • Author
Posted (edited)

Realizing I'm a beginner, I took it to the watch guy at the mall who popped it off in 2 minutes.  Though with much effort.  All that fighting get the balance swinging again to boot!

Thank all very much!

Edited by Lc130
Link to comment
Share on other sites
  • 3 years later...
GuyMontag Super WRT Addict

GuyMontag

Posted
Posted (edited)

I have this exact same watch and am having the same issue getting the back off. The watch came from a watchmakers estate and has been sitting in a drawer since the 70's so I don't think it would be glued on, I just think this case is a real bear to open.

I've tried my case knife as well as one of these snapback case openers that I have successfully previously used on stubborn cases, but it's only dinging up the case and ruining the blade on the case opener.  The stem is loose on this watch and it's not a split stem and the watch won't come out the front after removing the crystal so I'm not sure what to try next. I guess I'll give a razor a try as well.

 

This is the same watch after disassembly.

 

 

61JYoZ4wSVL._AC_UL1000_.thumb.jpg.d800ddf1230021e0c4ee7e9d5617760e.jpg

 

Edited by GuyMontag
Link to comment
Share on other sites
  • 1 month later...
GuyMontag Super WRT Addict

GuyMontag

Posted
Posted

I came back to this watch today and when I looked at the caseback seam under a scope I could see there *was* a lip where a case knife would fit but when the last person who worked on the watch put the caseback on they put the lip underneath the lug, which is curved towards the caseback. That made it difficult to get access to as the lug was in the way, but I was able to get a razor blade in the lip and pop the caseback off.

  • Like 1
Link to comment
Share on other sites
noirrac1j Distinguished Member

noirrac1j

Posted
Posted
15 hours ago, GuyMontag said:

I came back to this watch today and when I looked at the caseback seam under a scope I could see there *was* a lip where a case knife would fit but when the last person who worked on the watch put the caseback on they put the lip underneath the lug, which is curved towards the caseback. That made it difficult to get access to as the lug was in the way, but I was able to get a razor blade in the lip and pop the caseback off.

Small victories are what life is about!

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • nevenbekriev
      Windin pinion making

      By nevenbekriev · Posted

      The final result is not perfect looking, but is working well. The wheel is pritty small - the OD is 1.8mm
    • Neverenoughwatches
      Part swapper to part maker

      By Neverenoughwatches · Posted

      Thanks Rich, its really not that difficult to make them, simple ones anyway. Cousins didn't have the part though i could find it on ebay at 6.50. I figure i earned about £1.50/ hr . It paid for the diamond files i bought.
    • mikepilk
      How to remove shock settings from Smiths 512 movement

      By mikepilk · Posted

      If you look at this thread, you can see I had exactly the same problems with balance springs with 2 prongs on a Smiths 627. The slots in the chaton were not big enough to get the ends of the spring out. I had to bend them to get them out and back in. Not ideal. I don't fancy having to do it again as they could easily break, and where would you find replacements? I didn't come across the 3 prong type.     
    • mikepilk
      Breguet Exhibition at London Science Museum

      By mikepilk · Posted

      I visited the Breguet Exhibition today. https://www.sciencemuseum.org.uk/about-us/press-office/rare-timepieces-unveiled-new-display-science-museum The Science Museum now holds the collection of "The Worshipful Company of Clockmakers" - "The collection includes more than 600 watches, 90 clocks, 30 marine chronometers and a number of fine sundials and examples of hand engraving, mapping the history of innovation in watch and clock making in London from 1600 to the present day." It's well worth a visit. They have some amazing pieces by the likes of Harrison, Breguet, Tompion etc . I've visited twice before but decided to go and see the Breguet Exhibition. Maybe I was expecting too much, as on reflection, "More than 20 extraordinary timepieces designed by inventor and watchmaker Abraham-Louis Breguet " isn't going to take up that much space. In reality, it's just one cabinet. But, Oh those watches, stunning 🤩 , e.g. (No 1297 was made for George III and is valued about £1m)   I tried a couple of pics, but with subdued lighting and taking through glass, they aren't good. I like thin hands on a watch - how about these (I think this is a split second chrono)   And this one, with all it's complications, is only 10mm thick !   What I found very interesting were a few very old machines for making watch parts, like this 17th Century gear cutter. The disc below has concentric rings with holes in, so that is can be set to cut varying teeth numbers.       
    • RobS
      How to remove shock settings from Smiths 512 movement

      By RobS · Posted

      Firstly sorry for poor image quality I only have an iPhone for photos.    Im working on a 512 movement and I’ve had some trouble with the “jewels”. I’ve got the metal one out, but when I tried to put it back the three sides of the spring seem to need pressing all at once to fit it as there are three “holes”. I get two corners in but as I go for the third the first two pop out! Constantly I’ve lost the spring. I’ve done the similar ones on seiko movements without trouble. Assuming I find it/a replacement, what am I missing!   on the other side with the only ruby in the movement is a setting with no “gap”at all. How do I get the spring out, and of course get it back in!    What am I missing!    thanks in advance.    Rob
×
×
  • Create New...