Jump to content

What problem does the stop lever (hack) actually solve?


Stian

Recommended Posts

Hi guys,

I understand that the hack stops the balance wheel when setting the watch. However, I don't really understand why this is necessary? Can anyone enlighten me?

Thanks,

Stian

Sent from my VIE-L09 using Tapatalk

Link to comment
Share on other sites

Allows you to synchronize the watch seconds.  

Say in reality the time is 2:05:35 without hack you could set it to 2:05 easily, but if the watch is running, trying to get the seconds running on 35 is impossible.

Edited by Ishima
  • Like 1
Link to comment
Share on other sites

It was important for military chronometer-grade watches.

Y'know, "Gentlemen, synchronise your watches", etc. In the early days of WW2, the Weems watch was used for navigation. This was non-hacking and used a simple bezel like you see on divers watches to set the "zero seconds" point. Later, the MoD specified watches to be hacking, such as the IWC Mk11, so they could simply be set to the exact time by halting the movement while adjusting.

  • Like 1
Link to comment
Share on other sites

11 hours ago, Stian said:

I understand that the hack stops the balance wheel when setting the watch. However, I don't really understand why this is necessary? Can anyone enlighten me?

If you are looking for "necessary" in horology, you're looking into the wrong industry :D

  • Like 1
Link to comment
Share on other sites

Thanks a lot for the responses, very learningful. For non - chronographs though, does it not mean that every time you set the watch it also stops running? Probably not a big issue as such but probably not beneficial either?

Stian

Sent from my VIE-L09 using Tapatalk

Link to comment
Share on other sites

If you are looking for "necessary" in horology, you're looking into the wrong industry [emoji3]



Indeed, beneficial would be a better choice of words.

Stian

Sent from my VIE-L09 using Tapatalk

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Yes, Mine has a support for the blade that can be safely hit like this one https://www.amazon.co.uk/Rolson-62841-Tradesman-Knife/dp/B0044D9MC6/ref=sr_1_37?crid=3HWJF1HL4J8D7&dib=eyJ2IjoiMSJ9.X58oai8WcFho_-XqfR-lLQbU8lQKhf1vtFKAWbXR4EAhqVWR_eMy5h1DhaCULvkpA6XT0GaNFLHt_kJ0kPrhXFo0nYd8yJ4JgruoXDG9XjViAQOyAiBUkOhC9W9qQfGr0SMKpxIUrGOBkTjtTPTuM9IOTnb-dEAzbcZVvniVcEuMFGK9SITyDO6ryUU8ERkHt8f2Vy9Ks0QFO06KSJz65C2p7S3o2lOaUoO9kw61KyNtaaYYwdZzyuM2uRywODaigUn0u8RHMPR0dOa3WSrq8vE1iV5Et_561SFfvkhSGTQ.9QrdWVoCJpLVkrflNS1sxaY56ys4iiJspEFpUgLIRdg&dib_tag=se&keywords=stanley+knife&qid=1716289527&sprefix=stanley+knife%2Caps%2C77&sr=8-37 I use a brass hammer. You could use a very light pin hammer. A watchmaker's hammer would be a bit too light to use. I'm not sure of the weight, but looking at Cousins, it looks like a 60 or 84g brass hammer. I would go with the 84g one. A lot of the process is about feel, so you don't damage the case or bezel. Don't twist the tool! You may think it would make it easier and quicker, but that's when the damage starts to happen and be especially careful around the lugs. Once you have done a couple, you'll get a feel of it. Some bezels feel like they're not coming off and you start to doubt what you are doing. The trick is to be deliberate in your actions, rather than tentative. If you perform this task with the total belief that the bezel is coming off, that is exactly what will happen. First, be totally sure that the bezel comes off in the way you expect.   Rub the blade against a piece of 400 grit wet and dry until blunt
    • I do like the idea of clocks , you get so much more for your money than you do when buying a watch.
    • No but I have taken it out of its case to make sure all is well. 
    • I read recently that there are almost 600 different patterns of overcoil.
    • Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement.  Gabriel clocks are my thing.
×
×
  • Create New...