Jump to content

Upcoming Projects...

DJW

By DJW
in Your Watch Collection

 Share

Recommended Posts

DJW Super WRT Addict

DJW

Posted
  • Author
Posted (edited)

So I finished this build...mostly! I'm thinking of it as a "proof of concept"...

 

I decided not to do anything to the dial other than drill the markers at the hour marks, larger markers at the 12, 3, 6 and 9. This actually proved a problem after I remounted the dial and noticed that because the centerwheel pinion is off set from center, the minute and hour hands don't quite line up with the markers...not a huge deal though! Having said that, I think the dial looks Wonderful as it is! The simple dial/ markers really complements the "Busy-ness" of the skeleton movement.

 

post-90-0-79236000-1401825951_thumb.jpg

 

I also had to turn a back "Dial" to make up the difference of between the size of the movement and the size of the exhibition back crystal. This picture looks "deformed" but actually was taken at an angle to capture the best light.

 

post-90-0-17249000-1401825953_thumb.jpg

 

All in all, It will be something I do again now that I have an idea of what problems can and will arise when combining parts that were not designed to go together!

 

post-90-0-69429300-1401825954_thumb.jpg

Edited by DJW
  • Like 3
Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted (edited)

You've absolutely nailed that one Don, that really is one of the best looking watches I've seen.

I could happily wear it any way round because the rear is every bit as nice as the front!

:-)

Edited by Geo
Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
  • Author
Posted

You've absolutely nailed that one Don, that really is one of the best looking watches I've seen.

I could happily wear it any way round because the rear is every bit as nice as the front!

:-)

Thanks Geo! I think next time I'll use the rear dial to actually aid in holding the movement in place. Right now, it is just cemented to the case back. Also,You should see the "Engineering" I had to come up with to hold the movement in place! No less than 10 individual pieces to secure it!

  • Like 1
Link to comment
Share on other sites
carl Member

carl

Posted
Posted

This is very nice I like it. The combination of the components complement each other perfectly. May I ask where you get your cases from. I have couple of projects on the go at the moment and am struggling to find the right style case. The case on this watch would suit my needs i think. 

Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
  • Author
Posted

This is very nice I like it. The combination of the components complement each other perfectly. May I ask where you get your cases from. I have couple of projects on the go at the moment and am struggling to find the right style case. The case on this watch would suit my needs i think. 

Hi Carl, here is a link to the page where you can purchase these. If you sign up for a wholesale account, you get a good discount on the price. It does not cost anything to sign up.

http://www.dajiwatch.com/productshow1514.html

Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
  • Author
Posted (edited)

That`s one of the best looking watches I've seen. I would start building number two because number 1 will soon be sold.   :thumbsu:

Thanks autowind!

I think I'll keep this one! I know I say that about all the watches that I say I'm going to keep, but its time I need to actually wear something that I put together. But, I am going to order movement number 2 this week!

Edited by DJW
Link to comment
Share on other sites
  • 4 weeks later...
  • 2 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • mthomas828
      Balance staff sourcing?

      By mthomas828 · Posted

      Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
    • LittleWatchShop
      Movement holder made with 3D printer

      By LittleWatchShop · Posted

      Back home...printing now.  Will report results
    • VWatchie
      Epilame / Fixodrop

      By VWatchie · Posted

      Oh well, if Master @nickelsilver says it's the way to go, then it is the way to go! I stand corrected! 🫡 Are there any other places where you're supposed to remove the epilame from the contact point of rubbing? I don't think so! Thanks for the effort @Neverenoughwatches, much appreciated! 🙂👍
×
×
  • Create New...