Jump to content

Recommended Posts

Posted

High beat error, goofy bottom trace, but reasonable amplitude and timekeeping.

I haven’t checked properly, but I do believe the roller jewel is setting in the middle of the banks. I just C&O’d this one last week. I didn’t find anything wrong besides dirt.

1A51F7B9-A63A-4996-B7A1-0617A23B2B02.jpeg

Posted
1 hour ago, Woolshire said:

High beat error, goofy bottom trace, but reasonable amplitude and timekeeping.

I haven’t checked properly, but I do believe the roller jewel is setting in the middle of the banks. I just C&O’d this one last week. I didn’t find anything wrong besides dirt.

1A51F7B9-A63A-4996-B7A1-0617A23B2B02.jpeg

If it were the impulse jewel both tracks would likely have issues. In this case only one trace is off. Exit pallet not smooth. Loose pallet fork jewel perhaps.

 

On 1/27/2022 at 4:22 PM, JohnR725 said:

I suspected that that's where I saw that procedure because I knew I had seen it before.

But a lot of American pocket watches had round holes it really isn't an issue. A lot of American pocket watches have holes that are bigger than I would like to have its still not an issue it's just a pain you put the roller jewel in you put the shellac on you warm it up and then you very carefully get it all in alignment where it's supposed to be it can be done it's not as nice as if you have a hold the exact right size but it can be done you don't need a special tool you just did a little warm shellac and some tweezers and a lot of patience

Then while I said you don't need a special tool I assume that you do know that there is a tool to hold the roller table either where it's on the staff or it's off? I'll get a picture of that just so were all on the same page these I just assume that everyone knew that this tool exists but if you're modern watch repair why would you know such a thing.

Then because they were all in the same lecture I snipped out a few more images of roller jewel things. Even though they don't show a round jewel they did exist at one time.

That are variety of tools used to do the task the one that's labeled figure 12 is the most common one that's the most common tool available. It becomes an interesting procedure of holding the tool putting it in alcohol lamp melting the shellac hopefully not too much then holding on to the tool not touching anything because it's hot and carefully manipulating roller jewel.

Then found another image of what I call the conventional tool the advertising it can also be used to hold pallet forks.

Then I do know that there are other tools out there because I've seen one that holds the roller jewel nice and secure you lay the table on top of it then you keep that up either with the shellac reported after it's warm but it holds the jewel nice and straight get the table exactly where you want and then you go a put it back on the watch as opposed to doing it on the watch where things get really complicated.

roller jewel most common tool.JPG

roller jewel tools number two.JPG

roller jewel tools.JPG

roller jewel shapes.JPG

Pallet warmer roller watch.jpg

 

1 hour ago, Woolshire said:

High beat error, goofy bottom trace, but reasonable amplitude and timekeeping.

I haven’t checked properly, but I do believe the roller jewel is setting in the middle of the banks. I just C&O’d this one last week. I didn’t find anything wrong besides dirt.

1A51F7B9-A63A-4996-B7A1-0617A23B2B02.jpeg

 

A102601B-6BE6-4AFD-A375-D223D25AAA46.jpeg

  • Like 1
Posted
7 minutes ago, Woolshire said:

Likely exit jewel issue.

You would be the first who can tell if it is entry or exit jewel 😉

Frank

Posted

Or, the movement is not a tight fit in the case, giving a noisy signal. I've seen similar, but when just the movement is mounted on the timegrapher, I see a clean trace.

Posted

Well, took it apart to have a peek. Turns out both pallet stone faces are “wiped”. In other words, there’s a groove worn in both of them. I couldn’t see it until I used tons of light and a 10x loupe.

I’ve never seen that before. It a 1960’s Gruen 25J auto date, so nothing exotic. The movement plates look new but this poor thing was run hard with no lubrication for a long time…at least that’s my take on it.

Posted
8 hours ago, Woolshire said:

Well, took it apart to have a peek. Turns out both pallet stone faces are “wiped”. In other words, there’s a groove worn in both of them. I couldn’t see it until I used tons of light and a 10x loupe.

I’ve never seen that before. It a 1960’s Gruen 25J auto date, so nothing exotic. The movement plates look new but this poor thing was run hard with no lubrication for a long time…at least that’s my take on it.

Are you sure it's not stubborn old oil? The pallet stones are harder than steel so they shouldn't wear down... as is my understanding.

Posted
9 hours ago, Woolshire said:

poor thing was run hard with no lubrication for a long time…at least that’s my take on it.

While Sapphire supposed to be really really hard I have seen where it's been cut? Some more out the University used to be there somebody was talking about improper use of surface treatment? The problem was when you use surface treatment the solvent is extremely volatile or at least used to be it's supposed to be better now. The extremely volatile substance evaporates really fast and because of that it causes a cooling effect like Winfrey on evaporates basically and you get condensation. So I've seen claims that if you use surface treatment incorrectly water will get trapped in her on in the parts will rust. So somebody showed I believe was the roller jewel of the sliced into by the rusty pallet fork but?

It would still be worth taking something hard and scraping on the jewels just to make sure it's not ancient lubrication that is turned to stone.

9 hours ago, Woolshire said:

1960’s Gruen 25J auto date

I don't suppose you can narrow it down and give us an exact model number?

9 hours ago, Woolshire said:

Turns out both pallet stone faces are “wiped”. In other words, there’s a groove worn in both of them. I couldn’t see it until I used tons of light and a 10x loupe.

Minor problem here though if both of them are bad wire we only seeing it on one line?

Posted

JohnR, your speech to text software did not pan out very well in that post in the first paragraph. Can not follow.

You should probably also check the escape wheel teeth. If those two components have been working together for a while, the escape wheel will have suffered worse than the pallet jewels.

Meanwhile, it's not just the steel on sapphire, it's the steel on sapphire plus whatever contaminants get in there. Silica being the most likely suspect to my mind, which is much harder than steel as well. I'm reminded of automotive engines. Specifically performance oriented engines. The bearings in your passenger car will last hundreds of thousands of miles, but a performance engine will rarely last 50k. The way most people build them, that comes down to air filtration. To get more air, they remove the restrictive filters (or use "gravel catchers" that just keep out the big stuff). The byproduct of this is that silica dust suspended in the air by the tires of other cars gets in, eats up the rings/cylinder walls, gets in the oil and subsequently chews up bearings. Rebuild time. Same deal. The different hardnesses and lubrications SHOULD keep everything copacetic, but external contaminants find a way.

  • Like 1
Posted
3 hours ago, spectre6000 said:

your speech to text software did not pan out very well in that post in the first paragraph. Can not follow.

Yes my dictation software is temperamental basically it means from time to time I have to stare at the screen and question what the heck is it thinking and if I don't it gets mad at me and decides to just do whatever it feels like for words and it's really hard to read.

Destruction of escapement's? The surface treatment solution applied in the field to prevent lubrication from spreading has been rumored to cause steel components to rust if not applied properly. They used to be a website the person had pictures of the roller jewel and the Pallet fork both destroyed and covered with a light coating of rust. that is the possibility of one source of the problem

one of my acquaintances worked for Swatch group and anything resembling escapement issues they just replace both the escape wheel and the pallet fork. From our discussion it seemed like they were doing a lot of?

If you get into clock repair the steel pallets will usually get cut because particles of bad stuff in the air that we breathe embed themselves into the brass and they will slowly sliced through the steel pallets. All you need is the right grinding compound and a heck of a lot of time.

 

 

Posted

I believe it is a Gruen 710. Pretty positive each stone had grooves. One had a tiny pit, too. That might explain the timegrapher trace. I didn’t see anything on the escape wheel teeth. 
it is interesting that the watch keeps excellent time on my wrist and a visual of the balance would tell me the watch is like new. I guess that’s why we have machines to tell us what’s really going on!

Thanks to everyone for the replies and thoughts on this. I might look for a parts movement and change out the escapement. That will fix the beat error but then it probably won’t keep time.😱

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • This was what I was afraid of. The movement is not one of the generic black square modules. Remove the movement from the clock and try prying it open very carefully, without breaking the plastic tabs. The plastic might be brittle from age. Clean the wheels and check the battery contacts for corrosion. Check the PCB for bad solder joints. Take plenty of photos along the way.
    • One of the problems with trying to Photograph Phils things are that his enjoyment was building these things so they tended to E falls on what will see if I can find some earlier pictures or any pictures I wasn't even sure because I was looking for that specific picture for somebody else and even it got the last version and that would have been the last version. You will note that he put the indexing on something that he could unscrew it or whatever and it can slide back out of the way so the rest of the lathe can be used as a lathe. With the lathe cut are actually coming down from the top I was there once where he demonstrated how to cut a pivot with the setup it was really beautiful. Older set up if I remember it's not a worm gear assembly in the thing in between the stepping motor and the holding block I believe this particular one was like a 100 to 1 gear ratio. Earlier version with watchmaker's lathe. Even looks like he is the watchmakers bed and then switch to something he made. Then I do have other pictures and things of the rotary stage in use. In the raw so if you tube videos here is an example of one were somebody's mounting a three jaw chuck. At one time there were available on eBay they were not cheap but if you're patient like I was I found one cheap on eBay. After you watch the video it look at his other videos he is a whole bunch of other examples of the same rotary stage. That I do know there are other pictures examples and possibly videos you just have to track them down. One of the minor issues of finding this particular tech sheet for the unit is I believe it was a custom manufacturer and the company change their name but I remember the new name here's a link to the company https://www.ondrivesus.com/rino-mechanical-components                
    • Escapement adjusting always interesting and depending upon the reference always confusing. Okay maybe it's not always confusing but it does lead to confusion. I have a PDF below it's actually a whole bunch of separate stuff including a hand out that came from a lecture that's on you tube. Then from that we get this image Consequences of doing things especially if you do things out of order or you do things for the wrong reason. Oh and even if the watches working I made the mistake one so showing my boss how tweaking the banking pins on a full plate on the timing machine made the amplitude get better and now he thinks that's what they're for and I don't think a fully grasped exactly what horn clearance means. Consequence of doing things. Notice what it says about opening and closing the banking pins and total lock? So yes I've had that on a full plate where it won't unlock at all and that's the banking pins or a combination of things basically. So banking pins unfortunately get moved. One of the ways to tell if it's been moved is the look straight down at the end of the fork with the balance wheel removed. Power on the fork push at the one side look at it push it to the other side also look at it and compare anything with the center reference the balance jewel and see if both sides of the same. No guarantee after the same there in the right place but at least are the same typically when people play with things one side will be way off from the other because they had no idea what they were doing at all because of course it's a full plate and you really have to paying attention and even then there's still hard to do. Then the other thing that comes up like it shows below is people often adjust the banking pins to do all those other things as opposed to horn clearance which is all that it's therefore and maybe bonus Guard pin clearance although you're supposed to deal with the guard pin is a separate thing like single roller gets bent in Or out or sometimes physically gets moved in and out. Some full plates older escapement's typically pallet forks held together with screws and you can actually unscrew and move the entire assembly in Or out more complications to deal with.     Escapement handout wostep nscc.pdf
    • If he was much younger and some sort of sports player it wouldn't be a problem. They would be in there and doing surgery and he'd be back on the field in no time. Unfortunately when you get older little things are bad and big things can be really bad so not good at all.
    • Where I work everything incoming watches whatever detailed descriptions are taken entered into a computer program and photograph of each item. Then ideally although it depends on who's doing the paperwork detailed descriptions can be quite good other times there lacking. Like I really like it with pocket watches if they would record the serial number it avoids confusion later on. Then when watch repairs are completed that is also entered in. It's one of the amusements I learned when I was in school instructor had a shop and commented about the important aspect of keeping detailed records of repairs. Because oftentimes a customer who got a new crystal will come back later on when the watch doesn't work and expect you to fix the entire watch for free. Then you can remind them that they just got a crystal. Strangely enough that keeps coming up or occasionally comes up where I work now. One of the problems of using the service marks on the case is that in the case of pocket watches oftentimes that's not the original case. Then case marks? What I was doing warranty work for a company I used to describe a code number in the back of the case and it would tell me the next time I see the watch that basically what I did I made no attempt at keeping track of customers because we had literally thousands of them I think they sold 30,000 of these watches and they would come back by the hundreds because they had a lifetime warranty. Yes that's a story all of itself but I would put a code number that would reference what was done to the watch the last time and think I had a date in there somehow so it did tell a story if you knew the code. Another shop I once worked out the number would reference the page in the book. So other than knowing we had been in there you would have no idea what happened because you have to go look at the page in the book to see what happened. Then the problem of how you examine a watch you should examine the watch in detail every single time to avoid complications. Although on vintage watches and this is a of amusement I have at work when people ask something and I say of the watches done when it leaves. This is because on vintage oftentimes problems won't show up until the watches much farther into the repair like it's now running and you discover things that you can't discover before because it wasn't running to discover them that also become sometimes difficult to have exact rigid prices are estimates of repairs or in the case of a pocket watch you may not find out if a casing problem to later on when you case it up in the watches running. I was just thinking for all those people that would like to leave a mark maybe you should learn to do what some of the past watchmakers did? Leave a mark but leave it in such a way that no one will ever find it? Typically not done for repair purposes but done for other reasons like identifying it's legit. I have a friend with a Gruen watch and one of the Roman numbers the bottom line that just looks like a line under extreme magnification actually says Gruen watch company or something equivalent. So here's a link showing how to mark your watch without being seen although that's not the actual title. So if you can learn micro engraving you can engrave the watch someplace probably just about any place you just have to remember where you put it. https://cnaluxury.channelnewsasia.com/obsessions/how-to-prove-if-watches-are-authentic-secret-signatures-182516  
×
×
  • Create New...